Headphone Wall Hanger and Holder with Cable Groove - 3 Lengths, Tape or Screws
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A wall mount for headphones in three lengths, with a stiff 4 mm plate and a groove that holds the coiled cable.
- Rating
- 0 / 5
- Likes
- 2
- Downloads
- 8
- Makes
- 0
- Views
- 29
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Audio
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
A headphone wall hanger has one job, and the first version of this one failed at it. It looked right, but its back plate flexed just enough to peel the tape from the top down, and sooner or later the headphones ended up on the floor. This version keeps the same saddle and footprint and fixes the part you never see: a 4 mm plate that stays flat, plus two hidden screw holes for walls that do not get along with tape.
Which length fits your headphones
The 92 mm version is the one on my wall. It was designed for headphones with a suspension strap in the first place, fits most of them and still leaves room for the cable. The 76 mm version fits most headphones with an ordinary padded headband, and the 60 mm one, the shortest, fits most consumer headphones with a regular headband. To pick one, measure your headband from front to back where it rests on your head. It has to fit on the flat part of the saddle, which is about 67 mm long on the 92, 51 mm on the 76 and 35 mm on the 60. Gaming headsets hang the same way, as long as the band fits on that flat part. All three share the same plate, saddle and cable groove, and each one comes with the small soundblooms mark on the front or as a plain file.
92 mm - 1 h 58 min, 37 g
76 mm - 1 h 40 min, 33 g
60 mm - 1 h 23 min, 29 g
These are Bambu Studio estimates for PETG on a P1S. The plain files print two or three minutes faster.

Designed with the cable in mind
Right at the plate there is a groove that runs across the whole arm, 12 mm wide and 4 mm deep. Coil the cable, lay the coil into the groove and hang the headphones in front. The loops hang down along the wall between the earcups, and nothing ends up on the desk or the floor. Three turns of an ordinary 4 mm cable fit side by side, and a longer cable can go round a few more times on top of them.

Sizes of the saddle and the wall plate
The saddle is 70 mm wide and curved across like the top of a head, at an 85 mm radius, so the headband rests on its whole width instead of balancing on one edge. A 2.5 mm lip at the far end stops it from sliding off. The saddle sits 11.3 mm below the top edge of the plate, which is what makes the groove deep enough to hold the coil. The plate itself is 70 x 50 mm and 4 mm thick, against 1.6 mm on the first version, which makes it about 15 times stiffer in bending. Every number on the drawings was measured on the files you download.

Tape or screws on the wall
Both work, on the same part. For tape, use foam mounting tape made for plastics, such as 3M VHB or tesa Powerbond. Mirror tape is made for glass, and it was the first thing to let go on the old hanger. Sand the back flat, wipe it with isopropyl alcohol, press it hard against the wall and give it a day before you hang anything on it. For screws, there are two countersunk holes under the arm for 3.5 to 4 mm wood screws, with wall plugs if your wall needs them. They sit 30 mm apart and 28 mm below the top edge of the plate, and the screwdriver reaches them straight from the front, between the side walls of the arm. On the 92 mm version, with a big pair hanging at the far end, I would use the screws.

Printing the hanger
Print it lying on its back: plate on the bed, arm pointing up. It needs no supports and no brim. I use PETG because it takes a constant load better than PLA, with 0.2 mm layers, 4 walls, 15 % gyroid infill and 5 top and 5 bottom layers. A textured bed leaves its pattern on the back, and tape holds best on a smooth surface. The 3MF files are ready-to-print projects for a Bambu Lab P1S with a 0.4 mm nozzle and the textured PEI plate. Pick your own filament before you start, and if the hanger is going on tape, switch to a smooth plate before slicing or sand the back flat afterwards.

About the pictures
The first photos are of real prints: two of my 92 mm hangers in matte beige PETG, shot in a light tent, and the same hanger holding my headphones. The saddle and the arm come from my earlier hanger, which I printed and used every day. The other pictures are renders of the STL files in filaments from my shelf. On the cover the three lengths hang on a generated concrete texture, and the headphones in the renders are a generic model, not a real product.

I post my other audio prints, apps and DAC measurements at soundblooms.com. If you have a question or an idea, come and say hello on Discord.