1 / 5
Crown-Up / Crown-Down Watch Stand – Rests on the Lugs, Crown Touches Nothing, 34–42.5 mm Cases — image 1
1 / 5

Crown-Up / Crown-Down Watch Stand – Rests on the Lugs, Crown Touches Nothing, 34–42.5 mm Cases

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Stands a watch on its side, 3 o'clock up or down, on its lugs and caseback; crown and pushers hang free in an open slot.

Rating
0 / 5
Likes
0
Downloads
0
Makes
0
Views
15
Reviews
0

Updated at source:

Model information

Category
Bedroom
License
Creative Commons — Attribution — Noncommercial

All images are renders. This design is digitally validated; it has not been physically printed or tested.

A one-piece rest that stands a closed, round mechanical watch on its side - 3 o'clock down or 3 o'clock up - carried by its two lower lug horns and its caseback. The crown, crown guards and chronograph pushers hang in an open-front slot and touch nothing. The dial faces you, reclined 28°, and the closed strap or bracelet loops round the slim column. Turn the watch over in its own dial plane to switch between the two poses.

Validation status (please read): checked in CAD (fit of a watch family built from published dimensions, crown clearances, a calculated lean-back) and in the slicer (no supports). It has not been physically printed or tested. All pictures are renders of the CAD model with generic, unbranded watch proxies - none is a photograph.

Features

  • Carried by the lugs and the caseback: in the CAD check the case, crown, guards and pushers stay at least 4.6 mm from the flanks and the slot for every watch in the family below (crown at 3 o'clock; 4 o'clock crowns - see Limitations).

  • The crown hangs in open air at least 6.9 mm above the slot floor, visible from the front.

  • One print for the whole family - no sizes, inserts or adjustments: the watch's own lug-to-lug length sets the seat height.

  • The V seat centres the watch in its own dial plane; the 28° recline keeps the head leaning back on the column (calculated lean-back at least 0.6 mm for every checked watch, the strap not counted).

  • One part, no supports, no hardware; a flat underside for optional self-adhesive bumpers or a felt sheet.

Will my watch fit?

Checked in CAD for round watches with lugs: case 33.8-42.5 mm, lug-to-lug 40.4-49.9 mm, lug width 17-22 mm, 3 o'clock up and down. The check used the published case / lug-to-lug / lug-width dimensions (mm) of these watches; crown, guard and pusher sizes were estimated where they are not published:

  • Seiko SRP841 (33.8 / 40.4 / 17), NOMOS Tangente 35 (35 / 45 / 18), Orient Bambino 36, 38 and 40.5, Hamilton Khaki Field 38 (38 / 47 / 20), Tudor Black Bay 58 (39 / 47.5 / 20), Seiko SPB143 (40.5 / 47.6 / 20)

  • Rolex Submariner 41 (41 / 47.6 / 21), Omega Speedmaster Moonwatch (42 / 47.5 / 20, pushers at 2 and 4), Omega Seamaster 300M (42 / 49.9 / 20, valve at 10), Seiko SKX007 (42.5 / 46 / 22, crown at 4 o'clock)

Not affiliated with or endorsed by any watch maker; names are trademarks of their owners and are listed only as fit-check examples.

How to use it

  1. Close the strap or bracelet.

  2. Hold the watch dial toward you with 3 o'clock down (or up) and drop the strap loop over the column.

  3. Lower the watch until its lugs sit on the two sloped flanks; the caseback leans on the column.

  4. To switch poses, lift it, turn it half a turn in its own dial plane and set it down again.

Print settings

  • PLA (matte) or PETG. Avoid abrasive filaments (carbon, glass or metal fill) where the lugs sit.

  • 0.4 mm nozzle, 0.20 mm layers, 4 walls, 30 % gyroid, no supports, flat bottom on the bed.

  • About 52 g and 4 h 25 min (PrusaSlicer 2.9.6 estimate, generic profile).

  • Optional: 4 small self-adhesive bumpers or a felt sheet under the flat underside.

Files

  • crown-float-watch-rest_PLA.3mf - ready-to-print PrusaSlicer project: part placed, settings embedded (generic 220 x 220 mm printer profile - switch to your printer, press Arrange, slice).

  • crown-float-watch-rest.stl / .step - the model.

  • model.py - CadQuery source: flank gap and angle, recline and column size for other watches.

Dimensions

Footprint 84 x 74.7 mm, height 39.1 mm, dial recline 28° from vertical, flanks at 50° with a 37.5 mm gap between their edges.

Limitations

  • A resting pose only: no effect on accuracy or rate is claimed; resting positions affect every watch differently.

  • Round cases with lugs only. Not for cushion cases, integrated bracelets, rectangular or hooded-lug cases, or watches with a lug-to-lug length below about 40 mm (they drop between the flanks).

  • 4 o'clock crowns with crown guards (SKX-style): 3 o'clock down clears in the CAD check only with estimated guard sizes - check your watch; 3 o'clock up is the safe pose.

  • Use it with the strap or bracelet closed round the column. An open, hanging bracelet was not checked; a wide or stiff bracelet may touch the flanks behind the lugs.

  • Printed plastic touches the lug horns and the caseback - wipe the rest clean.

  • A light rest (about 52 g): a sideways push of about 1.8 N at the top of a large watch can tip it over (calculated). Bumpers or felt help it grip the surface.

  • Not physically printed or tested; real lug shapes vary.

Pictures

Renders of the CAD model, not photographs: a chronograph 3 o'clock down on a nightstand (cover), a close-up of the free-hanging crown and pushers, the same pose on a studio background, a dress watch 3 o'clock up, and the dimensions. The watches are generic proxies without logos.

Tags