1 / 7
No-Drill Shower Shelf for Bar Thermostats – Sits on Top of the Mixer, Hose and Handles Stay Free — image 1
1 / 7

No-Drill Shower Shelf for Bar Thermostats – Sits on Top of the Mixer, Hose and Handles Stay Free

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Shower shelf that rests on top of an exposed round bar thermostat, braced on the tiles. No drilling; lifts off to clean.

Rating
0 / 5
Likes
3
Downloads
4
Makes
0
Views
23
Reviews
0

Updated at source:

Model information

Category
Bathroom
License
Creative Commons — Attribution — Noncommercial

A one-piece, no-drill shower shelf that sits on top of an exposed bar thermostat - the horizontal chrome mixer bar on two wall unions, hose outlet underneath. The top of the bar is at hand height in the middle of the shower, exactly where shampoo is wanted. A 90° V rests on the top of any round bar body 36-48 mm across; the bar bears on the slope nearer the wall, which presses the shelf's back onto the tiles. Nothing clamps the chrome, nothing hangs below the bar except a leg against the tiles behind it, so the hose, outlet and handles stay free. Four flat gauge cards, printed first, tell you which of the three presets fits your mixer.

Validation status (please read): digitally validated only - fit, statics and drainage are computed from the CAD model and from mixer datasheet dimension ranges. It has not been physically printed or tested on a real mixer. All images are renders of the exported CAD or diagrams; the mixer, tiles, hose, bottles and soap are generic stand-ins - none is a photograph.

Features

  • Uses the spot that is already there: the top of the bar, with nothing below it to tangle the hose.

  • Computed not to tip forward or back under load: checked for 2 kg at the front edge, in the middle or against the backsplash, and for a 1 kg press on the front rail or near the wall (contacts taken as frictionless). A 44 mm leg behind the bar braces front loads; the backsplash braces loads near the wall.

  • Sideways: pushed along the bar, it slides 4.5 to about 30 mm (depending on your wall-pipe spacing) and then stops at the leg or a union nut - on the CAD nothing else touches first, for wall-pipe centres of 125-175 mm.

  • Drainage: a slotted deck that falls 3.5° to a flared front rail with water windows; on the CAD deck no water stays. The back touches the tiles only along narrow flats between drain grooves (about 28 % of its face), and the backsplash top is bevelled.

  • One support-free print, no drilling, no adhesive, no clips - it lifts straight off for cleaning.

Which preset?

Preset

Bar centre from the tiles

Deck inside (W x D)

Overall W x H x D

Highest point above the bar top

A

72-79 mm

96 x 103 mm

101 x 138 x 116 mm

up to 64 mm

B (default)

79-86 mm

96 x 110 mm

101 x 145 x 123 mm

up to 71 mm

C

86-93 mm

96 x 117 mm

101 x 152 x 130 mm

up to 78 mm

All presets: round bar bodies 36-48 mm, a plain bar of at least 185 mm between the handles. The deck holds about two bottles side by side plus a soap bar. Bottles need their own height above the deck, below any slide-rail bracket or hand-shower holder.

Gauge cards (print first; a slot = the 72 mm limit card, 1 / 2 / 3 holes = A / B / C): hold a card upright with its straight edge flat on the tiles, in the middle of the bar, and let its V rest on the bar. Look at the V from the front and to one side, past the handle (a phone torch behind it helps). A gap between the bar and the slope nearer the wall means the card is too small; the right preset is the smallest card with no gap on the wall side. The 72 mm card must show a gap - if it doesn't, the bar is too close to the wall; if even card C shows a gap, it is too far.

Files

  • thermostat-shelf-gauge-cards_PETG.3mf - the four cards (print first).

  • thermostat-shelf-A / B / C_complete_PETG.3mf - the shelf for each preset.

  • STL files of the three shelves and the cards, and model.py - the CadQuery source (wall distance, bar range, deck size, fall). Only the three presets were checked.

Print settings

  • PETG - it lives wet in a warm shower; PLA is not recommended. Any colour.

  • 0.4 mm nozzle, 0.20 mm layers, no supports, no brim, no skirt. As exported: the wall face flat on the bed, deck and fins standing up. 4 perimeters and 20 % gyroid are set in the projects; the cards print solid.

  • Only the narrow flats of the wall face touch the bed - use a textured or glue-coated sheet and clean it well.

  • Cards 2 h 30 min / 39 g; shelf A 12 h 9 min / 134 g, B 12 h 37 min / 144 g, C 13 h 11 min / 154 g (PrusaSlicer estimates on a deliberately slow generic profile).

How to use it

  1. Pick the preset with the gauge cards and print that shelf.

  2. Lower the shelf onto the bar from above, with the leg passing between the bar and the tiles, until its back rests flat on the tiles. Centre it between the escutcheons.

  3. Put the bottles on it, heavier ones toward the middle. Items narrower than 30 mm belong in the middle of the deck.

  4. Now and then, lift it off, rinse it and wipe the tiles behind it.

Limitations

  • It rests by gravity. Empty, about 0.3 N pushed up at the front rail (roughly 30 g of force) starts to rock it back slightly, and a knock from below or the hose dragged up against it can lift it off. Bottles on it make it proportionally steadier. It is not a grab rail.

  • Designed for up to 2 kg of bottles (computed from the CAD; no physical load trial).

  • Round bar bodies only - not for square or block bodies, top-outlet or central-body valves, concealed thermostats, or mixers with a built-in shelf. A bulge or taper in the bar under the shelf gives narrower sideways support.

  • Take it off before a thermostat thermal-disinfection flush (70 °C or more); PETG softens at about 80 °C.

  • Not physically printed or tested.

Pictures

Renders of the exported CAD and a computed drawing, not photographs: the shelf on a bar thermostat (cover), the shelf alone, a section through the saddle, the view from below with the hose free, a gauge card on the bar, the wall side and the dimensions with the three presets.

Tags