1 / 2
Wedge '86 - 80s Neon Supercar with Working Pop-Up Headlights — image 1
1 / 2

Wedge '86 - 80s Neon Supercar with Working Pop-Up Headlights

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Original 80s wedge supercar, about 1:24, with working pop-up headlights and spinning wheels. No glue or screws.

Rating
0 / 5
Likes
1
Downloads
2
Makes
0
Views
17
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

Pure 80s neon-night energy. Wedge '86 is an original late-80s wedge supercar at about 1:24, with working pop-up headlights and spinning wheels. Everything is printed: no glue, screws or magnets. It's an original design and doesn't copy any real car or brand.

WHAT MOVES

  • Both pop-up headlights flip up to about 80 degrees and click into place, then click down flush with the bonnet

  • All 4 wheels spin

FEATURES

  • A knife-edge nose, a steep wedge windscreen, a louvred engine cover and side intakes with fins

  • A big rear wing, a full-width red tail band and quad exhausts

  • Classic "dial" wheels, with wider tyres at the rear

  • Flush-fit black glass and a slatted rear louvre

  • Separate lenses, tail panel and exhaust tips, so you can do multi-colour without an AMS

  • Size: 177 x 83 x 40 mm. The largest part is the body (177 x 83 x 36 mm), so it fits any 256 mm bed

  • 16 part designs, 29 pieces, all on one plate

PARTS (the quantity is in the file name)

  • 01 body: body colour (hot pink, teal, white, red...)

  • 02 headlight pod x2: body colour

  • 03 headlight lens x2: white or clear

  • 04 windscreen: black or smoked PETG

  • 05 side window x2: black or smoked PETG (flip one over for the right side)

  • 06 rear louvre: black

  • 07 rear wing: body colour or black

  • 08 tail lamp panel: red or translucent red

  • 09 exhaust tip x4: silver

  • 10/11 rim front/rear x2: white, gold or silver

  • 12/13 tyre front/rear x2: black (TPU works too)

  • 14 wheel cap x4: same as the rims

  • 15/16 axle front/rear: any colour

PRINT SETTINGS

  • The 3MF is ready to print: 0.2 mm layers, 7% gyroid infill, tree supports set to auto (the slicer only adds them where a part needs them)

  • Every part is already oriented: the body prints upright, the wing upside down, the rims face down and the glass flat

  • Use 100% infill for the pods, axles, caps and exhaust tips

  • Roughly 100-130 g of filament

  • Hot pink, teal or white with black glass looks amazing. TPU tyres work too

ASSEMBLY

  1. Wheels: push each tyre onto its rim from the back. The rear tyres are the wider ones.

  2. Axles:
    a. Push each axle through the tunnel between its wheel arches.
    b. Slide the wheels on.
    c. Press a cap onto each axle end.

  3. Pop-up headlights:
    a. Press a lens into the lamp face (the underside) of each pod.
    b. Hold the pod open at about 45 degrees.
    c. Press its two side pins down into the slots at the rear of the headlight pocket. They snap in past a small narrowing.
    d. Fold the pod down flush. It clicks closed, and clicks again when flipped fully up.

  4. Glass:
    - Press the windscreen, side windows and rear louvre into their recesses. They sit flush.
    - The louvre slats face outward.

  5. Rear:
    - Push the tail-lamp panel into the tail recess.
    - Push the 4 exhaust tips into the holes.
    - Push the wing's two legs into the sockets on the rear deck.

TIPS

  • If a pod is loose and won't stay up, print the pods at 101% in Y.

  • If a pod is too tight, sand its sides lightly.

  • A tight tyre: sand the rim barrel. A loose tyre: print the tyres at 99.5%.

Tags