E-Ink Beer Tap Handle for Santek EZ Sign
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Remixed this model to use the Santek EZ Sign 2.9" E-Ink display. Heat-set a SS nut. Updates via NFC from your phone!
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 0
- Makes
- 0
- Views
- 20
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Kitchen
- License
- Creative Commons — Attribution — Noncommercial
Overview and Basic Info
There's several models on Printables for the Waveshare 2.7" passive NFC E-Ink display, however the prices of those have gone up and you can get two of the Santek EZ Sign 2.9" displays for the price. Since I have 4 taps I didn't want to spend $160 on Waveshare displays.
The Santek EZ Sign can be updated over NFC from your phone with their app, EZ Sign NFC. I heat-set a 3/8"-16 stainless steel hex nut into the handle with my soldering iron so the threads will be nice and durable.
A note on color versus black and white E-Ink tags
When choosing between color (4-color) and black and white (2-color) variants of the EZ Sign, note that color has the following drawbacks:
Due to extra filter layers, the base "white" of the color tag appears as a darker gray than the B&W tag; since these displays are not backlit this may hinder legibility depending on lighting conditions in your room.
The color tag takes around 20 seconds to update, whereas the B&W one takes just 3 seconds.
Since these same 4 color (black, white, yellow, red) E-Ink tags are used for store price tags, I found the color EZ Sign looked like, well, a store price tag.
Here's an image showing the two side-by-side in the tap handle to help you decide:

A note on tap faucets themselves
If you have rear-sealing faucets that get sticky and require a strong pull, I recommend trying out just the 3D printed shell with the recommended print settings before investing in all the E-Ink tags. It's no secret that 3D printed parts are less strong than injection-molded parts. When I printed the original model this was remixed from, it cracked right up the layer lines the first time the tap got sticky. While I made some model improvements and suggested print settings that increase the strength, your experiences may vary.
If you have forward-sealing faucets like Perlick, Intertap, Nukatap you won't have any issues. I'm in the process of replacing my rear-sealing stainless faucets with solid stainless Intertap D1210's as each keg runs out and it's quite the upgrade. The Intertap D1210 pulls smooth even after sitting unused for weeks.
Materials List
Product links to Amazon are affiliate links; if you find this model useful and need supplies, I'd appreciate you buying through the link to support my efforts at no extra cost to you. I always link the exact items I used during the make so it goes together flawlessly!
Required components for the assembly
(QTY 1) 2.9" Santek EZ Sign, black & white
or 4 color 2.9" EZ Sign (see above for pros/cons)
(QTY 1) M3 flat head screw, any length between 6mm to 20mm works
(QTY 1) 3/8"-16 stainless steel hex nut
Required tools
A cheap soldering iron (or some other way of heating the nut past the plastic's glass transition temperature to set it)
Appropriate size allen key for your M3 screws
Marker
Print instructions:
PLA has a slightly stronger raw tensile strength than PETG, so I printed my handles in PLA. This was printed on my Prusa MK3S+ with a 0.4mm nozzle and the 0.2mm "quality" profile in PrusaSlicer.
Cover:
No slicer modifications necessary.
Handle:
6 perimeters (increases strength)
Add a modifier block to the bottom narrowest part of the handle roughly 40mm tall to where the neck starts to widen and set this area to 100% infill for maximum strength when pulling the tap.
Printed with the forward-facing surface down, I used Hilbert Curve for my bottom fill pattern to get a more interesting look. I slowed first layer speed down to 15 mm/s to get a better result on my MK3S+.
Assembly
Remove your current handle, thread the jam nut all the way down, then thread on the 3/8"-16 stainless nut all the way to the bottom.
Mark the bottom of the first corner of the hexagon clockwise past the centerline with the marker. This will ensure you only have to back the jam nut off a little bit to square up the handle and get maximum thread engagement:

Secure the handle in a vise or clamp (wrap with a towel for protection). Flip the nut now that the handle is flipped, and put the marked corner facing what will be the front/display of the handle:

Set your soldering iron to 400C+ and press down on the nut. The heat cartridge of mine grabbed inside the threads. It took probably 20 seconds to dump enough heat into the nut to start seeing movement. Steadily press downward until the nut is flush with the bottom of the handle. If your soldering iron seems like it will get stuck in the nut, keep a chisel or other flat metal tool nearby to provide counter-force when removing the soldering iron without also ripping the nut from the melted plastic.

Drop the Santek EZ Sign into the cutout, insert the cover at an angle to drop it in, then secure with your M3 screw. If there's any play in the display, a folded paper towel under the cover leg should provide enough of a shim to hold it tight.
Thread the handle onto your tap, use the jam nut to center the display and upload your graphics with the EZ Sign NFC app.
Making Graphics for the Santek EZ Sign
The best way to make a sign is to make an exact 128x296 pixel canvas image with a white background in a graphics editor like GIMP, add your text/graphics, export as a .png and save to files on your phone. Since a pixel can only be black or white and not gray, the display cannot dither and downscaling will result in eliminated details. Making a pixel-perfect image ensures what you see is mostly what you get when uploading to the sign via the EZ Sign NFC app.
I found https://flaticon.com to be a decent source of free PNG outline clipart to use on my displays.