Crown headband inspired by Six The Musical
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A customisable spiked crown headband inspired by the costume or Catherine of Aragon from Six The Musical.
- Rating
- 0 / 5
- Likes
- 2
- Downloads
- 7
- Makes
- 0
- Views
- 45
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Cosplay & Costumes in general
- License
- Creative Commons — Public Domain
Crown headband inspired by Catherine of Aragon from Six The Musical
This is a fully customisable headband to create a crown like headband inspired by Catherine of Aragon's costume in Six The Musical. Everything is made from one OpenSCAD file, headband.scad, and can be changed in OpenSCAD's Customizer without touching the code.

Printing the default design
The default is a two-row headband: 12 spikes along the front and 11 behind them, attached with a simple press fit.
Open the file. Load headband.scad in OpenSCAD and open the Customizer (Window → Customizer).
Print a test piece first. Set What to make → part to Test print of the selected connection, render (F6) and export an STL. Print it and push the spike into the hole. If it's too loose or too tight, adjust Press fit → pressFitAllowance by about 0.05 mm and print another test piece.
Export the headband. Set part to Headband, render (F6) and export.
Export the spikes. Set part to Spikes to print, render and export. This gives one spike of each height. The console tells you how many of each to print. For the defaults that's:
12 spikes of 45 mm
5 spikes of 67.5 mm
6 spikes of 22.1 mm
Assemble. Push each spike into its hole. The front row is all 45 mm spikes. The back row alternates tall and short, starting with a tall spike in the centre.
Print settings
Orientation: print both parts exactly as exported. The headband lies flat on its edge and the spikes stand upright. Neither needs supports, unless you enable the recess for ears.
Material: PLA works. PETG is a little more forgiving for the band's flex and for snap-fit spikes.
Brim: if required, use one on the tall spikes. They stand on a small base.
Walls: three or more walls (perimeters) on the band make it stronger, since it is only 3.9 mm thick. I like to use 4 walls with 0% infill for the spikes.
Layer height: 0.2 mm is fine. Use 0.12 mm or finer for the threaded connection.
Previewing
Set part to Headband with spikes (preview only) to see everything assembled. It's for checking the look and spacing, not for printing.
Customising
Every setting in the Customizer has a short description and, where it helps, a slider. Messages starting with WARNING appear in the console when a setting won't work, for example spikes that overlap or stick out past the edge of the band.
Settings that take a list
A few settings hold one value per row, typed as text:
| separates rows, front row first.
, separates spike heights within a row.
If there are fewer values than rows, the last value is reused for the rest.
Setting | Default | Meaning |
|---|---|---|
numSpikes | 12 | 11 | 12 spikes in the front row, 11 in the row behind |
spikeReach | 0.5 | 0.45 | How far down each side the spikes go, per row: 0 = top only, 0.9 = almost to the ears |
spikeHeights | 45 | 67.5, 22.1 | Front row all 45 mm; back row alternates 67.5 and 22.1 mm from the centre |
rowGapAdjust | 0 | Fine-tunes each gap between rows in mm, e.g. -1 | 2 |
Some examples:
One row of 12: numSpikes = 12
Three rows: numSpikes = 12 | 11 | 10 and spikeReach = 0.5 | 0.45 | 0.4
Same pattern on every row: spikeHeights = 67.5, 22.1
Single centre spike: numSpikes = 1
An even number of spikes has no spike in the centre. An odd number has one.
The Customizer sections
Spikes: how many and where. The list settings above.
Spike shape. spikeDiameter sets the width of each spike's base. The holes in the band always match it. spikeTipRadius sets how sharp the points are.
Rows. rowSpacing is the distance between rows. rowTaperLength controls how gradually the band narrows again after the last spike of a back row. Extra rows make the band wider only where they need to; the ends near the ears stay normal width.
Fit to the head.
headContourRadius curves the back rows down to follow the shape of your head from front to back. Smaller curves more; 0 is flat.
curveWholeBand curves the whole band, front row included. This works with a single row too.
Connection. How the spikes attach. Each method has its own section of settings.
Method | Holds | Removable | Notes |
|---|---|---|---|
Press fit | Friction | Pull out | Simplest. Tune with pressFitAllowance. |
Snap fit | Barbs click in behind a lip | With a firm tug, or permanent (snapRemovable) | Spikes must be at least about 14 mm tall. |
Screw from the inside | M3 countersunk screw | Yes, with a screwdriver | Default needs an M3 × 10 mm screw. Can use a heat-set insert (screwAnchor). |
Threaded | Spike screws into the band | Yes, by hand | Holes go right through the band. Slow to render in older OpenSCAD (see below). |
holeInnerSkin leaves a thin layer at the bottom of each hole so nothing touches your head. Threaded holes always go right through.
Band size.
Setting | Controls |
|---|---|
bandSpan | Width ear to ear |
bandHeightRatio | Height of the arch compared with its width |
bandWidth | Width of the band itself, front to back |
bandThickness | Thickness of the band |
endGapRatio | Gap between the two ends |
flareEnds | Curves the ends in to hug the head |
Ears.
thinEars makes the band thinner where it passes the ears, for comfort. It stays the same width.
earCutout cuts a notch in the edge to clear the back of each ear. A front-edge notch prints with a short bridge over it. A back-edge notch prints with no overhang.
Inner teeth. Small teeth along the inside help the band grip your hair. toothedRatio sets how far down each side they go; 0 turns them off.
Test print. A short piece of band with one hole, plus a short spike, for checking the selected connection before printing everything. Small dots beside the hole show which connection it is: 1 press, 2 snap, 3 screw, 4 threaded.
Preview colours and quality. quality switches between Draft (faster previews) and Final (use this when exporting). The colours only affect the preview.
OpenSCAD version
The file works in OpenSCAD 2021.01 and later. The threaded connection is very slow to render in 2021.01, so for threads use a recent development build with the Manifold engine turned on in Preferences (where it lives varies between builds). It renders the threaded headband in about a minute.
https://github.com/paulbrouwersnz/3d-crown-catherine-of-aragon-six-the-musical
