1 / 4
Tablet and Phone Holder for the Round 16 mm Kitchen Rail (Fits IKEA HULTARP) – Clicks On From the Front — image 1
1 / 4

Tablet and Phone Holder for the Round 16 mm Kitchen Rail (Fits IKEA HULTARP) – Clicks On From the Front

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Hangs a cased tablet (landscape) or a phone on a round 16 mm kitchen rail: recipe at eye level, counter clear.

Rating
0 / 5
Likes
1
Downloads
1
Makes
0
Views
21
Reviews
0

Updated at source:

Model information

Category
Kitchen
License
Creative Commons — Attribution — Noncommercial

RailRest is a one-piece cradle that hangs a cased tablet (landscape) or a phone on a round 16 mm kitchen rail - the size of IKEA HULTARP - so a recipe stays at eye level and off the counter. It clicks onto the rail from the front, swings back until its rounded foot rests on the wall, and the device stands on its ledge leaning back against it. The clip wraps the rail and opens toward the wall, so the device's weight and taps on the screen press the rail into solid material. It does not hook over the rail from above: the cradle itself stands only 1.8-2.3 mm above the rail (calculated on the CAD, by file). Three sizes from one profile - Tablet, Tablet-Deep for thick cases and Phone with a cable slot - each in two bore sizes, plus a small tester card.

Validation status (please read): checked in CAD (clip fit and click force, swing to the wall, device envelope, retention, strength - all calculated) and in the slicer (no supports). It has not been physically printed or tested - please report. Images are renders of the CAD model and drawings from it, not photographs; the tablet, phone, rail and kitchen in the images are generic stand-ins. "Fits IKEA HULTARP" describes compatibility with the rail's published 16 mm diameter - this is not an IKEA product.

What you need

3D printed (PETG or ASA, not PLA):

  • tester card - print it first

  • 1 cradle - Tablet, Tablet-Deep or Phone, bore b165 or b167: the file the tester card picks

Not printed: nothing - no screws, glue, tape or other hardware.

You need to have: a round 16 mm kitchen rail (IKEA HULTARP size), its centre 12-44 mm from the wall, and your tablet or phone (with or without a case) within its file's limits.

Optional, your own: a USB-C cable with a straight plug, to charge a phone through the Phone file's cable slot.

Everything is 3D printed - no hardware required.

Features

  • Clicks on from the front and stays on: at rest and under taps toward the wall the rail reaction stays at least 16° inside the solid part of the clip, for every supported device and every rail-to-wall distance of 12-44 mm (calculated). Forcing the rail back out through the narrower opening takes about 20 N or more (calculated with a low friction coefficient of 0.3, weakest file).

  • Tugged straight toward you at its bottom, it swings out and back and stays on the rail - calculated for a level tug of up to 13 N at the ledge; a press down on the ledge of up to 10 N does not push it off either (calculated, weakest file, quasi-static - a steady pull, not a jerk).

  • Swings back to the wall when you let go (calculated with at least 4.3x margin over the clip's friction, friction coefficient 0.5 assumed).

  • Low above the rail: the cradle needs only its clip's 1.8-2.3 mm (calculated on the CAD, by file); landscape tablets and phones stay low (see the table).

  • One part, printed on its side with no supports; every bend runs along the printed layers.

Which file?

Sizes: height from the clip's top down, depth from the wall.

  • Tablet (120 mm wide, 203 mm tall, 122 mm deep, about 160 g): 11-13 in tablets in landscape and 8.3 in tablets in portrait or landscape, with a case up to 20 mm thick and 1.0 kg (8.3 in: 0.45 kg). Large tablets in portrait are not supported.

  • Tablet-Deep (128 mm deep, about 162 g): the same tablets in thick cases of 20-26 mm.

  • Phone (66 mm wide, 184 mm tall, 110 mm deep, about 80 g): phones in portrait or landscape with a case up to 14 mm thick and 300 g; a slot through the ledge lets a straight USB-C plug hang down from a bottom port (calculated for phones 8.6-14 mm thick, bare or in a case, port centred in the thickness).

  • Each in bore 16.5 (b165) or 16.7 (b167, for printers whose holes come out small) - the tester card picks it.

Device in a case

File

Device top above the rail's top (calculated)

13 in tablet, landscape

Tablet / Tablet-Deep

up to 24 mm / up to 26 mm

11 in tablet, landscape

Tablet / Tablet-Deep

below the rail's top

8.3 in tablet, portrait

Tablet / Tablet-Deep

up to 5 mm / up to 8 mm

8.3 in tablet, landscape

Tablet / Tablet-Deep

below the rail's top

phone, portrait or landscape

Phone

below the rail's top

Lean of the device (calculated): about 23° with the rail centre 12 mm from the wall down to about 13° (tablet) / 12° (phone) at 44 mm. Measure from the wall to the front of the rail and subtract 8 mm. Device sizes are references only - check your device's published size and weight.

Print the tester card first

  1. Rings: the ring with one dot is 16.5 mm, the ring with two dots 16.7 mm. Hang the card below the rail and push each ring up onto it. Both turn freely -> print b165; only the two-dot ring -> print b167; neither -> check your printer's hole size or your rail and do not print the cradle.

  2. Gap tabs: hold the card on edge, square to the wall, its end against the wall, and slide the tabs between the wall and the rail. The 4 mm tab must pass; the 36 mm tab must not. Otherwise the rail centre is closer than 12 mm or farther than 44 mm from the wall - not checked.

  3. Slots: your device, in its case if it has one, must slide into the 20 mm slot (Tablet), 26 mm (Tablet-Deep) or 14 mm (Phone).

Files and print settings

  • Ready-to-print PrusaSlicer projects: railrest_tester_card (40 min, 9 g), railrest_tablet_b165 / _b167 (about 11 h 6-9 min, 158-159 g), railrest_tablet_deep_b165 / _b167 (about 11 h 17 min, 161 g), railrest_phone_b165 / _b167 (about 5 h 47-48 min, 82 g) - PrusaSlicer 2.9.6 estimates on a generic PETG profile, 0.2 mm.

  • STL files of every cradle and the tester card, and model.py - the parametric CadQuery source (bore, clip wall / hood / jaw, lean, drop, ledge, lip, width, cable slot).

  • PETG or ASA - not PLA (kitchen warmth and the constant load make PLA creep). 0.4 mm nozzle, 0.2 mm layers, no supports; the cradle on its side as in the projects, with a 3 mm brim - peel it off, including the thin skin inside the clip's opening and in the narrow gap between the clip and the back plate; the tester card flat, no brim.

How to use it

  1. Put it on: hold the empty cradle by its clip, the opening toward the wall and just above the rail, its bottom a little away from the wall, and push the clip back onto the rail along the opening - toward the wall and slightly down - until it clicks (a firm push, calculated at about 41-43 N depending on the file, friction coefficient 0.5 assumed). Let go: it swings back until the foot rests on the wall.

  2. Stand the device on the ledge and lean it back against the cradle. Phone with a cable: push the plug down through the slot from above first, then plug in the phone.

  3. Take it off: lift the device out, grip the clip itself (close to the wall, pinch it top and bottom) and pull it off along the opening - toward you and slightly up - with a firm pull.

Limitations

  • Not physically printed or tested; fit, click force, swing and stability are calculations on the CAD.

  • Round 16 mm rails only (checked against HULTARP's published diameter) - not KUNGSFORS (13 mm) or square rails; rail centre 12-44 mm from the wall.

  • The device is not clamped: a pull of about 0.3-1.8 N toward you at its top edge (calculated) lifts it forward out of the cradle; the lip stops its bottom from sliding forward. Taps toward the wall are fine (calculated for a 5 N tap at the device's top).

  • A push from below (a hand or a pot) of a few newtons (calculated; less than 1 N for the empty cradle) lifts the foot off the wall and swings the cradle up - the device can tip out, and a strong enough push can force the clip off. Keep the space under it clear. A harder tug at the bottom than stated above can pull it off - it is designed to come off with a firm pull.

  • Pushed sideways along the rail it slides from about 1.0 N with a device in it (about 0.3-0.5 N empty; calculated, low friction 0.3 assumed) - that is also how you move it.

  • PETG creeps a little under constant load: over months the click may get lighter - check it now and then.

  • Large (11-13 in) tablets in landscape only. Keep it away from the hob and splashes; not splash-proof.

Pictures

Renders of the CAD model and drawings, not photographs: a tablet and a phone on a kitchen rail (cover), how it hangs and rests on the wall, the Tablet cradle (empty) and the Phone cradle, and the tester card with the lean table.

Tags