1 / 8
Vampire Fangs for Honda Civic Type R (FL5) - Halloween Edition — image 1
1 / 8

Vampire Fangs for Honda Civic Type R (FL5) - Halloween Edition

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Paint-safe, support-free Halloween vampire fangs/teeth for the Honda Civic Type R FL5. Fully modular with zip-tie locks

Rating
0 / 5
Likes
0
Downloads
2
Makes
0
Views
46
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

Get your FL5 ready for spooky season with these custom-designed Halloween vampire fangs for the front grille!

Unlike generic accessories, this is a fully engineered, modular kit designed for a secure, paint-safe fit without permanent modifications.

What's Included & File Notes

  • The Fang (Right & Left Side): Designed to look aggressive while keeping a safety clearance gap with the bodywork.

  • Backplate (Right & Left Side): The main structural mount that sits over the front grille.

  • Alignment Pins (x4 Total): Simple revolution pins that lock into the backplate (to be glued, with Loctite or hot glue, for example) and align with the grille's hexagonal mesh edges to restrict movement.

Paint & Bumper Protection System (Pro Tips)

  1. Piano Black Bumper Protection: Since the fangs sit just a few millimeters away from the paintwork, apply white electrical tape to the Piano Black trim right above the plastic grille. This serves a double purpose: it protects the sensitive Gloss Black finish from micro-scratches due to road vibration, and it seamlessly blends the gap between the fang and the car's body color!

  2. Grille Fabric Tape: Wrap fabric tape (wiring harness tape) around the plastic grille where zip ties make contact to prevent scratches.

Secure Mounting System

  • Zip-Tie Security: The backplate shall be anchored using up to 5 zip ties (max 5mm width; 3,5mm width is the optimal choice) at strategic points across the plastic grille hexagon (marked in red in the photo). It is quite challenging inserting the tape behind the grill (to protect it from the zip ties); do it with a bit of patience.

  • Locking Mechanism: The fang snaps into the backplate via 3 teeth. To lock it permanently while driving, feed a side zip tie through the fang (see fourth photo)—internal routing guides inside both parts will automatically loop the tie through and pop it out the back. Just push and tighten!

Print Settings & Recommendations

  • Orientation & Slicing: Default orientation is the correct one, with the flat area touching the build plate. 0,2mm layer height is enough in my experience, with 1,2mm thick walls and top/bottom layers and 25% infill.

  • No Supports Needed: Designed to print 100% support-free!

  • Nozzles: Optimized for both 0.4mm and 0.6mm nozzles.

  • Material: Standard PLA is completely fine for seasonal/Halloween use.

  • Color Setup: Print the backplate and pins in stealthy black, and the fangs in white or glow-in-the-dark/fluorescent filament.

Required Hardware

  • Standard zip ties (max 5mm width). I used 3,5mm wide zip ties, 5 for each backplate, and then another to secure the tooth to the backplate.

  • Fabric harness tape (to protect the grille from the zip ties and the backplate). Black electrical tape will work too.

  • White electrical tape (for the piano black trim over the grille). I used 3 layers for each tooth for added safety; there were a few scratches when I removed them.

  • Scissors to cut the tape, and an electrical wire cutter with a pointy flat head (to cut the zip ties flat after tightening them and then to remove them when dissasembling the teeth).

  • Loctite or hot glue. The pins should be press-fit into the backplates, but adding some glue is a good idea, just to be safe.

Changelog / Updates

  • 2026/10/30: Added room in the fangs for the zip-tie heads. In the first version, big zip ties would need to be cut behind the grill, which is nearly impossible. Now the zip-tie head can be installed from the front. Sorry about this!

  • 2026/11/02: I installed the teeth and used the car on multiple routes, bumpy roads, and at high speed. Everything went well. I'm happy with the design, so I'll just leave it as it is.

Note: This design includes a discrete author watermark and a non-commercial tag. Please respect the creator's work and do not sell printed copies of these files without consent.

Enjoy the spooky looks, snap some awesome photos, and Happy Halloween!

Tags