Grave Treats – Crank-Operated Tombstone Candy Dispenser
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Turn the moon. Click. The ghost jumps, and the grave gives you ONE treat… if you dare.
- Rating
- 0 / 5
- Likes
- 6
- Downloads
- 7
- Makes
- 0
- Views
- 70
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Autumn & Halloween
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Grave Treats – Crank-Operated Tombstone Candy Dispenser 🪦👻🍬
Turn the moon. Click. The ghost jumps, and the grave gives you ONE treat… if you dare.
Grave Treats is a working candy dispenser disguised as a cracked, weathered gothic tombstone on its own little graveyard: a stone pedestal, a framed crypt door, tufts of grass, a Celtic cross and a tiny neighbour tombstone, and a blood-red coffin with a golden cross. Fill the grave with Skittles, M&Ms or similar candy, then turn the full-moon crank on the side. Every quarter turn:
CLICK! The moon snaps into the next position with a satisfying detent.
BOO! The ghost floating above the grave jumps up and drops back down.
TREAT! Exactly one candy slides out through the crypt door into the blood-red, velvet-lined coffin.
Put it next to your door on Halloween night: no more kids grabbing a whole handful, and everybody wants to crank the moon.
How it works

Hopper: lift off the lid (the ghost comes with it) and pour candy into the grave. A 46° funnel guides it down to the drum.
Metering drum: the pumpkin-orange drum has 4 single-candy pockets. The top pocket fills from the funnel, a quarter turn later it empties into the chute.
Ghost cam: the left end of the drum carries a 4-lobe cam. The ghost stands on a push rod that runs through a sealed channel in the grave (no candy can get in) and up through the lid. Each lobe lifts the ghost 7.5 mm, and gravity brings it back down. The lobes sit 45° offset from the pockets, so the ghost is down in every rest position and jumps while you turn.
Click detent: a springy tongue is built into the right wall of the grave. Its little nub snaps into 4 dimples on the back of the moon crank. The square drive (instead of a hex) means the moon always fits in a position where clicks, pockets and ghost line up, however you put it on.
The crypt delivers: the candy drops into a shaft, slides down a 34° ramp, comes out through the framed, pointed crypt door and drops through a notch in the stone pedestal into the coffin.
(See the cross-section render for the full candy path.)
No screws, no glue: the Bone Snap Pin 🦴
The mechanism is held together by one printed snap pin with a little bone as its head:
Push it in from the moon side, through the crank, the drum and the left wall of the grave.
Its split, barbed tip clicks into place behind the left wall.
The bone head holds the moon crank on the drum, and the barb keeps the drum in the grave.
To take it apart for cleaning, squeeze the two prongs sticking out of the left wall together and pull the pin out.
Parts (6 + optional inlays, no supports needed)
# | Part | Orientation | Notes |
|---|---|---|---|
1 | Tombstone body | upright, plinth on bed | ~120 × 110 × 144 mm, includes the click tongue |
1 | Tombstone MULTICOLOR (3MF) | as is | body + text inlays as separate objects, for MMU/AMS |
2 | Lid (with bat) | flat cut face down | |
3 | Drum | standing, square drive up | teardrop pockets and the 45° cam groove print without support |
4 | Moon crank | flat, knob up | |
5 | Bone snap pin | flat (as exported) | 100 % infill |
6 | Ghost on a stick (waving arms) | flat (as exported) | 100 % infill, white or glow-in-the-dark |
All parts fit a 200 × 200 mm bed. Files are exported in print orientation.
Print settings
Layer height 0.2 mm, 3 perimeters, 15 % infill. Use 100 % infill for the snap pin and the ghost.
PLA or PETG (PETG gives a springier snap pin and click tongue)
No supports.
Colors (as in the renders)
Stone: dark slate grey · drum: pumpkin orange · moon: pale yellow · ghost: white (glow-in-the-dark ghost and moon look amazing!) · pin: bone white
"R.I.P. / TAKE ONE": glow-in-the-dark green · "TRICK OR TREAT": orange
Grass tufts: green · coffin lining: red · coffin cross: gold
Single-extruder? Paint the debossed text and cracks, or do a filament swap at the text layers. Paint the coffin red, the cross gold and the plinth top and grass tufts green. A quick dry-brush of light grey over the dark stone makes the cracks and the door frame pop.
The grass tufts are thin (1.2 mm) blades: print with 0.4 mm nozzle and 2 perimeters.
Assembly
Slide the drum into the round opening on the right side of the grave.
Put the moon crank on the square drive.
Push the bone snap pin through the crank, the drum and the left wall until it clicks.
Put the lid on and drop the ghost's stick through the hole in the lid until it rests on the cam.
Fill with candy and crank the moon!

Tolerances
Drum ↔ bore: 0.5 mm radial · square drive ↔ crank: 0.15 mm per side
Ghost rod ↔ channel: 0.4 mm per side
Snap pin ↔ wall hole: 0.2 mm, barb overlap 0.7 mm per prong
Click nub preload: 0.8 mm
If the pin is too hard to push in, scale it to 98 % in X/Y (not in length).
Candy compatibility
Pockets are Ø16 × 9 mm and work with candy up to about 14 mm across and 8 mm thick: Skittles, M&Ms, Reese's Pieces, jelly beans, small chocolate eggs. Peanut M&Ms are too big.
Designed in SolidCraft. Files include STEP and the native design so you can remix it.