1 / 2
Kent Single Lever Paddle Dust Cover (SP-1) — image 1
1 / 2

Kent Single Lever Paddle Dust Cover (SP-1)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Dust cover for the Kent single lever paddle. Sits on the base, keeps the lever usable, prints with no supports.

Rating
0 / 5
Likes
0
Downloads
0
Makes
0
Views
8
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution — Noncommercial — Share Alike

Overview

A dust cover for the Kent Single Paddle (SP-1). It rests on the top face of the steel base and its skirt wraps the base edge, so the cover never touches the desk or the mechanism. An arched notch at the front lets the lever pass through, so you can leave the cover on and still send. The callsign and KENT lettering are flush multicolor inlays, not raised or recessed text.

On the Air

Brass contacts and ball bearings collect dust fast on an open shack desk, and a single lever paddle tends to sit out between sessions. This cover keeps dust off the contacts, bearings and adjustment screws without having to be lifted off before a QSO. The cable exits under the Kent base, so there is no cable notch in the cover. This is the third in a set of paddle covers built on the same design, after the W1SFR Fat Boy and Blackstone covers.

Print Settings

- Printer: Bambu Lab X1C with AMS, 0.4 mm nozzle

- Material: PETG-CF for the body (the carbon fill hides layer lines on the large flat faces), plain PETG for the callsign inlay (gold) and the KENT inlay

- Layer height: 0.20 mm

- Supports: none required

- Orientation: upside down, top face on the plate. The inner rims have 45 degree gussets so they print as unsupported overhangs. The top face comes out flat and clean for the lettering.

The 3MF is set up for three filament slots: cover body (1), callsign (2), KENT (3). If you are not using an AMS, assign all three parts to one filament.

Hardware and Assembly

No hardware required. Set the cover over the paddle with the arched notch at the front, around the lever, and let the inner rim settle onto the top of the base.

Design Notes

Fitted to a measured Kent base of 76.45 x 101.52 x 16.2 mm on 7 mm feet. These measurements are slightly larger than Kent's published 75 x 100 x 15 mm, so measure your own key before printing and scale as needed if you wish.

- Clearance: 1.5 mm per side, 2.0 mm walls, 2.5 mm roof. Outside size is 83.5 x 108.5 x 44.7 mm.

- Inner rim: 3.5 mm on the base along the back and both sides. The rear adjustment screws sit about 5 mm in from the side edges, so the rim stops short of them. There is no rim at the front.

- Rear gap: the rear rim has a 40 mm gap in the center so it does not sit on the Kent label on the back of the base. Delete or resize it in the SCAD file if your key has no label.

- Headroom: the interior ceiling is 26 mm above the base top. The pivot block is 25.4 mm tall, so the margin is small. Check yours before printing.

- Lever notch: 18 mm wide arch, with its top 23 mm above the base top. The lever needs about 20 mm.

- Skirt: stops level with the bottom of the steel base and covers the base edge completely.

A 24 mm tall fit ring is included. It checks the skirt, the rims, the rear gap and the bottom of the notch for about a third of the filament. Print it first if your key might differ from these measurements. The ring does not check the pivot block headroom.

The OpenSCAD source is included and parametric. You can change the callsign, the base size, the clearances, the notch and the rear gap from the parameters at the top of the file. The KENT and callsign lettering are separate modifier volumes, so each can take its own color.

Makes, remixes and fit reports on other Kent keys are welcome, especially if your base measures differently.

Tags