1 / 6
70s Chopper Motorcycle Kit - V-Twin Hardtail with Working Steering, Spinning Wheels & Kickstand — image 1
1 / 6

70s Chopper Motorcycle Kit - V-Twin Hardtail with Working Steering, Spinning Wheels & Kickstand

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A 1:10 70s chopper kit with working steering, spinning wheels and a folding kickstand. Plug-together, no glue.

Rating
0 / 5
Likes
2
Downloads
16
Makes
0
Views
49
Reviews
0

Updated at source:

Model information

Category
Vehicles
License
Creative Commons — Attribution — Noncommercial

Long fork, tall apes, fat rear tyre, flames on the peanut tank: a full 70s custom chopper you build yourself. An original design (no brand logos) at about 1:10 scale, 268 mm long and 150 mm tall.

WORKING PARTS

  • The long raked telescopic fork steers, with built-in steering stops at about 38 degrees each way

  • Both spoked wheels spin: a skinny 21-inch-style front and a fat rear with drum brake

  • The kickstand folds down to park and swings up to ride

DETAILS

  • A 45-degree V-twin with finned barrels and heads, pushrod tubes, a cone air cleaner, primary and cam covers

  • A rigid hardtail frame with a bobbed rear fender, tail light and forward controls

  • A peanut tank with raised flames (paint them or use a colour change)

  • A king and queen seat with tuck-and-roll buttons and a tall sissy bar

  • A shotgun twin exhaust with fishtail ends

  • Everything is printed: no glue, screws, springs or magnets. Halves join with small printed pins

PRINT SETTINGS

  • The 3MF is ready to print with 5 plates: 0.16 mm layers for large parts, 0.12 mm for small detailed parts (engine fins, rims, headlight, pins), 0.4 mm nozzle, 3 walls, 15% gyroid infill, no supports

  • Pins, axles, washers and kickstand: 100% infill (already set in the 3MF)

  • Detect thin walls is ON: the spokes are 0.72-0.84 mm wide

  • Plates are grouped by colour: frame, engine/fork/exhaust and tank/seat (gold), rims (white), stays and pins (white) + tyres (swap to black or TPU)

  • TPU tyres work great, PLA works too

  • About 90 g of filament. Largest part 187 x 106 mm, needs a 200 mm bed or bigger

ASSEMBLY

  1. Engine: push 3 joining pins into one engine half and press the other half on.

  2. Frame + engine + fork: lay the left frame half inside up, set the engine in the cradle (pegs into holes), lay the fork's steering stem into the half head tube (bottom yoke below, top yoke above), push 5 joining pins in and press the right frame half on. The fork is now captured and steers.

  3. Rear stays: press each stay onto the two pegs on its side of the frame, flat side facing the wheel.

  4. Wheels: push two rim halves into each tyre, one from each side. Front wheel goes between the fork legs with the short axle pin; rear wheel between the stays with a washer each side and the long axle pin (drum on the left).

  5. Exhaust: press its two flange holes onto the pegs on the right side of the cylinder heads.

  6. Tank: pin the halves together (2 pins) and press onto the 2 backbone pegs. Seat: the same.

  7. Sissy bar: push its two legs into the holes on top of the oil-tank block.

  8. Headlight: spread the two ears under the bottom yoke slightly and clip it in. It tilts to aim.

  9. Kickstand: clip it onto the peg on the left under the engine.

TIPS

  • Pin or peg too tight? Sand it lightly. Joining pins loose? Print them at 103%

  • Turn the handlebars gently: the steering stops on its own at about 38 degrees

Original design by Kirimas Studio.

Tags