Rescue Helicopter - Geared Rotors (Main Rotor Turns the Tail Rotor), Sliding Door, No Supports
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Rescue helicopter kit with printed gears: turn the main rotor and the tail rotor spins. Sliding door, no supports.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 4
- Makes
- 0
- Views
- 16
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Vehicles
- License
- Creative Commons — Attribution — Noncommercial
An original rescue / utility helicopter kit with a real printed drivetrain. Turn the main rotor and printed crown and pinion gears hidden inside the fuselage drive a shaft down the tail boom to spin the tail rotor, about 1.4 times faster, just like the real thing. About 205 mm long with a 184 mm main rotor (about 1:72 scale).
WORKING PARTS
Geared rotors: a 20-tooth crown gear on the mast drives a 10-tooth pinion on a driveshaft down the tail boom, and a second pinion drives the 14-tooth tail rotor crown
The big cabin door on the right side slides open on two printed rails
A plug-in rescue winch arm with hook above the door
DETAILS
A rounded nose with split windscreen, cockpit and cabin windows, and an engine / gearbox hump with exhausts
A nose searchlight, a tail beacon, a horizontal stabiliser and a swept fin
A bolted tail gearbox drum, a one-piece 4-blade main rotor with blade grips, a 4-blade tail rotor and skids
Everything is printed: no glue, screws, springs or metal shafts. Parts plug together with printed pins
v1.1: thinner driveshaft middle (2.5 mm) so it spins freely in the tail boom channel
PRINT SETTINGS
The 3MF is ready to print with 3 plates: 0.16 mm layers, 0.4 mm nozzle, 3 walls, 15% gyroid infill, no supports
Gears: 0.12 mm layers, 100% infill, "detect thin walls" on (already set). Module 1.0 teeth print well on an A1. Keep elephant foot compensation on
Mast, driveshaft, tail rotor shaft and pins: 100% infill. The shafts are D-shaped and print flat on the D side
Plates are grouped by colour: fuselage, door and gearbox cover (white), rotors, skids and winch (gold), gears and shafts (any colour)
About 85 g of filament. The largest prints are the fuselage halves (205 x 80 mm) and the main rotor (184 x 184 mm). Fits an A1 / 256 mm bed
ASSEMBLY
Dry-fit the gears first; they should turn freely.
Gears onto shafts (all bores are D-shaped, match the flat): main crown gear onto the lower end of the mast, teeth down; a pinion onto each end of the driveshaft; tail crown gear onto the tail rotor shaft, teeth facing the boom.
Lay the left fuselage half inside up. Put the mast into the gearbox pocket (collar on top of the roof) and lay the driveshaft into the channel along the boom: the front pinion meshes under the main crown, the rear pinion goes into the tail gearbox.
Push 5 joining pins into the left half and press the right half on. Check that the mast turns the driveshaft.
Tail gearbox: slide the tail rotor shaft into the open gearbox on the left of the tail so the crown meshes with the rear pinion, press the cover in and press the tail rotor onto the square end.
Main rotor: press the hub onto the square top of the mast.
Door: slide its four mushroom pins into the front ends of the two rails on the right side. Slide back to open, forward to close.
Skids: push each skid's two pegs into the slanted sockets under the cabin. Winch: push its peg into the hole above the door.
TIPS
Gears stiff? Turn them by hand a few dozen times to wear in. A drop of dry PTFE lubricant helps
A gear loose on its shaft? Print the gears at 99.5% or the shafts at 101%
Door too tight? Run a needle file along the T-slot rail necks
Original design by Kirimas Studio.