LEGO Flying Ford Anglia Display Stand (Harry Potter 76424)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A curved stand for a small LEGO Ford Anglia, with a separate 2x4 mount and a tilted flying pose.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 2
- Makes
- 0
- Views
- 24
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Building Toys
- License
- Creative Commons — Attribution — Noncommercial
A flying pose for the Ford Anglia
A display stand inspired by Harry and Ron flying above the railway in their Ford Anglia. The smooth curved arm lifts the car off the shelf and gives it a left bank with the nose pitched down.
Designed around the smaller LEGO Ford Anglia with an approximate 120 × 50 mm footprint. This version includes one separate 2×4 stud mount. Check that the underside of your car has a suitable accessible mounting area near its centre.
Features and dimensions
Two printed parts: the base with curved arm, and the removable 2×4 mount.
Oval base: 100 × 76 mm, 5.6 mm thick.
Centre of the mounting surface: 110 mm above the shelf, excluding the studs.
Fixed flying pose: approximately 8° left bank and 12° nose down, with the front-left corner lowest.
Mount dimensions: 31.8 × 15.8 × 5.8 mm, including the studs.
Eight studs on an 8 mm grid. Stud diameter: 5.05 mm; stud height: 1.8 mm.
Keyed D-shaped connection sets the mounting direction. The broad seat supports the mount.
Both parts are designed to print without supports.
Files to print
anglia_flight_arm.stl — print once, with the oval base flat on the build plate.
anglia_flight_connector_2x4_flight.stl — print once, flat underside down and studs facing up.
Recommended print settings
Material: PETG. Translucent PETG can make the support less visually prominent.
Nozzle: 0.4 mm.
Base and arm: 0.16–0.20 mm layers, 2 walls and 100% infill. Aligned rectilinear is recommended when working on translucency.
2×4 mount: 0.12–0.16 mm layers, 3 walls and 100% infill.
Top and bottom: 4 layers each as a reliable starting point.
Supports: none. Keep the supplied print orientation.
Brim: normally unnecessary; add a small brim if needed for adhesion.
Seam: place it at the rear of the arm. Keep seam blobs away from the mating surfaces.
Translucent PETG tips
Dry the filament according to its manufacturer's instructions. For the base and arm, try slow extrusion speeds around 20–25 mm/s and 100% aligned rectilinear infill. These are starting points for tuning, not a guarantee of glass-clear results. Surface texture and the thickness of the arm also affect its appearance.
Keep the mount on a calibrated flow setting. Do not apply deliberate over-extrusion for transparency to the studs or socket: their fit depends on dimensional accuracy.
Assembly and fit
Test the mount on the D-shaped pin before attaching the car. Support the end of the arm while fitting the mount, then attach the car near the centre of its underside. Place the mount lengthwise along the chassis, with the car's front pointing towards the engraved arrow on the mount's underside. Carry the assembled display by its base; the connection has no locking latch.
The 5.05 mm stud geometry was physically tested in Bambu PETG Translucent and held very firmly while remaining removable. Your printer and settings may produce a different fit. Eight studs can also require more force than a smaller test piece.
It has an intentional snug fit; do not force it if your print is too tight. For a quick fit check, print the mount first. Do not scale the whole part to adjust fit, as that changes the stud spacing as well as the socket.
For indoor display use. The car is not included.
Not affiliated with or endorsed by the LEGO Group, Ford, or the Harry Potter rights holders.
