1 / 5
1950s Convertible Cruiser Kit - Opening Doors, Rolling Wheels & Swappable Top, No Supports — image 1
1 / 5

1950s Convertible Cruiser Kit - Opening Doors, Rolling Wheels & Swappable Top, No Supports

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

1950s-style convertible kit at 1:24: doors open, wheels roll, the top swaps up or folded. No glue, no supports.

Rating
0 / 5
Likes
0
Downloads
1
Makes
0
Views
12
Reviews
0

Updated at source:

Model information

Category
Vehicles
License
Creative Commons — Attribution — Noncommercial

Long, low and finned: an original 1950s-style two-door convertible cruiser kit at about 1:24 scale. It doesn't copy any real car or brand. About 236 x 86 x 55 mm with the top up.

WORKING PARTS

  • Both doors open on printed hinges and stop at about 70 degrees

  • All 4 wheels roll on printed axles, with whitewall tyres and full hub caps

  • Swappable convertible top: the raised soft top or the folded top stack, both press onto the same 4 pegs

  • The rear fender skirts clip off to show the rear wheels

DETAILS

  • Tail fins with bullet tail lamps and rear lamp bars

  • Hooded headlamps, a wide grille and a front bumper with bullet guards

  • A side spear, a full bench-seat interior with dash and a big thin-rim steering wheel

  • Made for multi-colour printing by parts: no painting needed

  • 22 STL files (38 parts). Everything is printed: no glue, screws, springs or magnets

PRINT SETTINGS

  • The 3MF is ready to print with 5 plates: 0.16 mm layers, 0.4 mm nozzle, 3 walls, 15% gyroid infill, no supports

  • Axles, hub caps and steering wheel: 100% infill (already set in the 3MF)

  • Plates are grouped by colour as in the photos: body, doors, fender skirts and tail lamps (red); windscreen frame, tops, interior, bumpers, grille, headlamps, rims and hub caps (gold); tyres (black), whitewall rings (white) and windscreen glass (clear PETG) - swap filament for the last plate

  • Every STL is already oriented. The body prints upright on its flat underside (the wheel-well tops are short 13 mm bridges). Doors and fender skirts print standing up; use a brim on the doors if your bed adhesion is weak

  • About 200 g of filament. Largest part: the body, 224 x 81 x 41 mm, so it fits a 256 mm bed (Bambu A1, P1, X1 and similar)

  • A smooth PEI plate gives the windscreen glass a glossy face

ASSEMBLY

  1. Wheels: push a tyre onto each rim from the back until it stops against the front lip, then press a whitewall ring into the groove on the outer face of the tyre.

  2. Interior: drop it onto the 4 pins in the cabin floor. Push the steering wheel column into the hole in the dash.

  3. Doors: set each door's bottom hinge hole onto the pin in the sill, with the small pin on top of the door pointing up.

  4. Windscreen: press the glass into the frame from the front. Lower the frame onto the cowl so its holes go over the cowl pegs and its corner bosses go over the door hinge pins. The frame now holds the doors.

  5. Axles: push an axle through each tunnel, slide the wheels on and press a hub cap onto each axle end. The wheel spins, the cap grips the axle.

  6. Front: press in the grille and both headlamps, then push the front bumper's two pegs into the nose.

  7. Rear: press the bullet tail lamps into the fin ends and the lamp bars into the rear panel, then push the rear bumper's pegs into the tail.

  8. Fender skirts: clip their two pegs into the holes around each rear arch.

  9. Top: press the raised top or the folded top onto the 4 pegs behind the doors.

TIPS

  • Tyre too tight? Sand the rim barrel lightly. Too loose? Print the tyres at 99.5%

  • Loose whitewall ring? Print the rings at 100.5%

  • Loose hub cap? Print the caps at 98% in X/Y

  • Open the doors gently: they stop on their own at about 70 degrees

Original design by Kirimas Studio.

Tags