1 / 5
Verity Minecraft mask with adjustable printed headgear — image 1
1 / 5

Verity Minecraft mask with adjustable printed headgear

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

240 mm wearable Verity mask with open eyes, adjustable printed headgear, yellow/black 3MF and individual STL files.

Rating
0 / 5
Likes
3
Downloads
5
Makes
0
Views
64
Reviews
0

Updated at source:

Model information

Category
Masks
License
Standard Digital File License

Wear Verity's yellow grin for a Minecraft costume or Halloween. This 240 mm mask has a shallow front shell, open eye holes and an adjustable printed harness. The rear cradle and crown strap help support the mask across the head.

The gallery images are digital renders, including the wearing illustration. Print times and material use below are slicer estimates.

Files and dimensions

The download includes a yellow/black 3MF project arranged on three plates for the Snapmaker U1, individual plate 3MFs, STL parts, assembly instructions and foam cutting templates. All printed headgear components are included.

  • Mask: 240 mm wide, 240 mm high and 74 mm deep.

  • Open eye holes with black borders and seven small smile vents.

  • Side straps: 48 mm adjustment range in 8 mm steps.

  • Crown strap: suggested working length of 276 to 348 mm.

Hardware and fit

  • 16 M3 heat-set inserts, 5 mm outside diameter and 4 mm long.

  • 14 M3 x 8 mm socket or button-head screws.

  • 2 M3 x 10 mm screws for the crown overlap clamp.

  • 3 to 5 mm self-adhesive foam for the forehead, rear cradle and underside of the crown join plate.

Six printed washers are included. Use the listed screw lengths: longer screws can bottom out. Insert pilot holes are 4.4 mm across and 5.5 mm deep. Set the side length first, then shorten the crown until it supports the mask and lines up both sight holes. Head and face shapes vary, so check clearance when fitting it to someone new.

Printing

The project uses PLA, 0.4 mm nozzles, 0.20 mm layers, five walls and 20% infill. Load yellow as filament 1 and black as filament 2. Keep the coloured mask parts together as a single multi-part print.

Print the shell with its rear rim on the bed and the face upwards. Tree supports are required inside the dome and under the forehead support. Saved settings use slim trees from the bed, a 35-degree threshold, three interface layers, a 0.20 mm top gap and a 5 mm brim.

The headgear parts print without supports in their supplied orientations. Keep the crown bands flat during printing. Curve them gently during assembly and avoid creasing them at the holes.

Plate

Parts

U1 estimate

1

Yellow shell and black face

19 h 13 min / 456 g

2

Rear cradle, carriers and end clamps

1 h 46 min / 83 g

3

Straps, join clamp, keepers and washers

1 h 25 min / 43 g

Total: about 22 hours 23 minutes and 582 g, including supports and prime-tower waste. Your filament and slicer settings will change these estimates.

The 3MF targets the U1's 270 mm bed. For another printer, use the individual STLs with your own machine profile and check the shell, brim and prime-tower fit. No other printer's print profile is included.

Assembly

The attached Assembly_Instructions.txt has the complete steps, hardware locations and part quantities. The three 3MF plates already contain the required quantities; each individual STL contains one part.

Install the inserts, attach the mirrored carriers, then fasten the side straps and rear cradle with M3 x 8 mm screws. Feed the long crown band through the opening near the top of the shell and clamp it to the internal anchor. Clamp the short band to the rear cradle. Use the two keeper loops to retain the overlap and join the bands with the insert plate, cover and two M3 x 10 mm screws.

For the middle crown setting, pair the last and third-last centre holes on the long band with the fifth and seventh centre holes on the short band. This gives a 308 mm setting. Shift both selected holes together to adjust in 8 mm steps.

Add foam, set the crown length and mask angle, then snug the screws. The rounded upper shell opening is the crown passage; keep it clear when removing supports. Check the view through both eye holes before walking around.

This is a fan-made costume mask inspired by Verity from Minecraft. It was made with AI assistance and checked for closed meshes, attachment clearances and plate fit, then sliced with the U1 profile.

Tags