Claude Halloween | Dress up Claude | Figure with 5 swap-on costumes in 2 sizes
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A little Claude figure with five Halloween costumes - print all or just one: witch, vampire, ghost, mummy, pumpkin
- Rating
- 0 / 5
- Likes
- 2
- Downloads
- 16
- Makes
- 0
- Views
- 106
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Autumn & Halloween
- License
- Standard Digital File License
Claude Halloween - one figure, five costumes
Dress up the little Claude figure for Halloween: a witch, a vampire, a ghost, a mummy and a pumpkin. The main piece of every costume slips on in one go and is locked by the figure's own arms - no glue.
Pull the arms out, slide the cape, sheet, body wrap or belt down over the head, push the arms back in through its side windows - done. Hats, caps and head wraps simply sit on the head. Change outfits whenever you like.
At a glance
- Figure: body, two eyes, two arms and a round base - eyes and arms press in, no glue.
- Costumes: witch (cape + hat), vampire (cape with collar and fangs), ghost (sheet), mummy (bandages) and pumpkin (belt + cap).
- Two sizes: L (figure on base 115 x 115 x 62 mm) and S (72 x 72 x 40 mm).
- Single colour or multicolour: every part prints on its own in one colour (one plate per colour). With an AMS, the witch's band, buckle and clasp, the vampire's collar lining and fangs and the mummy's seal can also print in place; the ghost clasp and the pumpkin stem and leaf always plug in.
- Three fits: standard, plus tight and loose versions of the parts that need it (body and costume shells).
- Colours: orange, black, plum and ivory - at most four per costume.
- Bed: every L part fits a 180 x 180 mm bed (largest: 130 mm (Witch hat brim)), every S part any bed.
What's included (parts per size, dressed size L / S, filament + time single colour L / S)
- Claude figure - 6 parts: orange body and arms, black eyes and base. 115 x 115 x 62 mm / 72 x 72 x 40 mm; 89 g, 2h 42m / 30 g, 1h 12m.
- Witch - 7 parts: black cape, ivory clasp, plum hat brim, hat pin and hat cone, orange hat band, ivory buckle. 130 x 130 x 116 mm / 81 x 81 x 74 mm; 92 g, 2h 54m / 30 g, 1h 30m.
- Vampire - 3 parts: black cape, plum collar lining, ivory fangs. 115 x 115 x 78 mm / 72 x 72 x 50 mm; 40 g, 1h 38m / 13 g, 58 min.
- Ghost - 2 parts: ivory sheet, plum clasp. 115 x 115 x 77 mm / 72 x 72 x 49 mm; 61 g, 2h 45m / 23 g, 1h 20m.
- Mummy - 3 parts: ivory body wrap and head wrap, plum seal. 115 x 115 x 87 mm / 72 x 72 x 55 mm; 50 g, 1h 53m / 17 g, 53 min.
- Pumpkin - 4 parts: orange belt and cap, plum stem, ivory leaf. 115 x 115 x 98 mm / 72 x 72 x 63 mm; 57 g, 2h 45m / 20 g, 1h 24m.
- Everything: about 389 g (L) / 134 g (S) of filament in single colour.
How it goes together
1. Press the eyes and arms into the body and set the figure on the base pegs.
2. To dress it: pull out both arms, slide the costume's main piece down from above, push the arms back in through its arm windows.
3. Hats, caps and wraps sit on the head; small details plug in (single colour) or are printed in place (AMS projects).
Printing
- PLA, 0.4 mm nozzle, 0.16 mm layers, 15 % infill. Every part comes oriented on its print face.
- Supports only where marked: a strip under the front band of the witch and vampire capes, and the ghost sheet's face window and four foot arches. The projects mark them (support enforcers); with the plain STLs add support just there, or load the included enforcer files together with the part. Everything else prints without support.
- First print: the S figure (about 1 h 10 min). Eyes or arms too stiff or too loose? Reprint only the body from the loose or tight set - all other figure parts are the same file in every fit. Same for the costumes: only the shells change.
Care
Display figure, not a toy for small children (small parts - the S hat pin is 3 mm). PLA softens at 55-60 °C: no hot car, no dishwasher.
Show your print
Printed one? Please post a make - I'd love to see which costume your Claude wears.
Fan art
Unofficial fan art of the Claude mascot. Not affiliated with, endorsed or sponsored by Anthropic. The Claude name and character belong to Anthropic; the licence below covers only my 3D design files.
AI Declaration
AI was used in the production in the following ways:
* Ideation (AI-generated concept images of the costumes)
* Text Creation (title and description)
* Images (renders made with AI-written render scripts)
License
This work is licensed under a Standard Digital File License.
Digital files have a strict non-commercial, personal use only license.
You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital file or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including remixes of this object).
You can not host these files on other digital platforms, web stores or cloud repositories.
The objects may not be used in any way whatsoever in which you charge money, collect fees.
✖ | No sharing or redistributing in any way of the 3D files or derivatives
✖ | No remixing
✖ | Non-commercial Use (only for personal use)