1 / 27
DIY Phone Tripod — image 1
1 / 27

DIY Phone Tripod

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Fully DIY adjustable tripod using 1/2" PVC and 1/2" wooden dowels

Rating
0 / 5
Likes
11
Downloads
15
Makes
0
Views
150
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

To build this model, you will need the following:

HARDWARE

  • Seven: M4x25mm screws

  • Seven: M4 nuts

  • Three: 24" (610mm) lengths of half-inch PVC pipe

  • One: 13" (330mm) length of half-inch PVC pipe

  • Three: 36" (915) lengths of half-inch wooden dowels

  • (OPTIONAL) One: 15x8mm circular bubble level

  • One: M6x180mm partially threaded rod

    • To build the model without the threaded rod, you will need to print

      • Tilt_UpperOPTIONAL instead of Tilt_Upper

      • Tilt_HandleOPTIONAL instead of Tilt_Handle

      • Tilt_RodOPTIONAL

TOOLS

  • M4 or 5/32" drill bit (and a way to use it)

  • Pliers

  • Glue of your choice (I strongly recommend CA/superglue)

  • Tape of your choice (I recommend masking tape)

PRINTED COMPONENTS (TRIPOD)

  • One: Upper_Hub

  • One: Lower_Hub

  • One: PVC_Adapter

  • One: Tilt_Block

  • One: Tilt_Upper or Tilt_UpperOPTIONAL (See above for which)

  • One: Tilt_Handle or Tilt_HandleOPTIONAL (See above for which)

  • One: Tilt_RodOPTIONAL (Only if not using the M6x180mm rod)

  • Three: Upper_Swivel

  • Three: Lower_Swivel (This is the only print that will require supports)

  • Three: Swivel_Ring

  • Three: PVC_Screwhole

  • Three: Height_Thumbscrew

  • Six: Swivel_Nut

  • Six: Swivel_Bolt

PRINTED COMPONENTS (PHONE CLAMP)

  • One: updated_phone_clamp_lower OR updated_phone_clamp_lower_thicker

  • One: updated_phone_clamp_upper OR updated_phone_clamp_upper_thicker

    • (opt for whichever one suits your phone better)

  • One: updated_phone_clamp_threads

  • One: Updated_Phone_Clamp_Knurl_Head_hole

  • One: Updated_Phone_Clamp_Screw_Bottom_hole

  • One: Updated_Phone_Clamp_Screw_Top_hole

DIRECTONS

  1. Print out all components, they can be printed with standard PLA/PLA+ settings (2x walls, 4x top/bottom, 20% infill). I recommend using a brim for maximum bed adhesion. The only print that will need supports is the Lower_Swivel. All files are already in their intended print orientations, so you don't need to change them in the slicer.

  2. Insert the Upper_Swivels and Lower_Swivel and align their through holes with the holes within their respective hubs. Then, slide the Swivel_Bolts through them and insert the Swivel_Nuts. If the Swivel_Nuts do not stay in place with just friction, carefully glue them in, making sure to not glue the nut to the hub.

  3. Screw the Swivel_Rings into the Lower_Swivels using three of the M4 nuts and screws, but do not overtighten. One side of the Swivel_Ring has an insert for the nut and the other is countersunk for the screws.

  4. Insert the 13" length of PVC through so that the top of the Upper_Hub is flush with the top of the pipe and the bottom of the Lower_Hub is flush with the bottom of the pipe, making sure that the hubs are aligned. If friction is not enough to hold them in place, wrap tape around the PVC until the friction is adequate.

  5. Insert the 24" PVC pipes through the Swivel_Rings and into the Upper_Swivels. If they do not stay in the Upper_Swivels with friction, either wrap tape around the pipe or carefully glue them in, making sure that they are inserted all the way into the upper swivels before the glue dries. Do not glue the pipes to the Swivel_Rings, as they should be free to slide along the PVC pipes.

  6. Using your pliers, insert an M4 nut into the pocket of the PVC_Screwhole print such that one of the corners of the hexagon is pointed upwards. Then, insert the PVC_Screwhole to the bottom of the 24" PVC legs, aligning the nut to the upper and lower swivels. Repeat for all three legs.

  7. Mark where the holes need to be drilled using the PVC_Screwholes as a jig. Using your 5/32" or M4 drill, drill out a hole through PVC and put the PVC_Screwholes back. Repeat for all three legs. DO NOT glue the PVC_Screwholes, as you may misalign the two holes and ruin the part

  8. Screw in three of the M4 screws into the three Height_Thumbscrews. They are deliberately a tight fit so you will have to torque them down a bit. I recommend adding some glue to the screwheads to secure the screws within the prints, just make sure that the M4 screw is all the way in the thumbscrew. These will serve as a way of adjusting the height of the wooden dowels. Then, screw them into the PVC_Screwholes, leaving room to insert the dowels.

  9. Insert the dowels into the PVC pipes and tighent down the Height_Thumbscrews after any and all glue has dried to avoid gluing them to the rest of the tripod.

  10. Glue the Tilt_Block to the PVC_Adapter and insert the PVC_Adapter into your 13" length of PVC, making sure not to accidentally glue the adapter to the PVC. If you don't have the amount of friction you desire between the adapter and the pipe, wrap tape around the adapter until you get the effect you want.

  11. Insert an M4 nut into whichever Tilt_Upper you printed and screw it into the Tilt_Block using an M4 screw

    1. If you are using the threaded rod, screw one end of the rod into the Tilt_Upper and then screw the Tilt_Handle onto the other end.

    2. If you are using the printed handle, insert the Tilt_RodOPTIONAL into the Tilt_UpperOPTIONAL, then insert the Tilt_HandleOPTIONAL onto the other end. If friction is not enough to hold the parts in place, use glue to hold them in

  12. Assemble Stamos' Tripod Mobile Phone Clamp V2 Remix, and glue the flat, bottom base of whichever thickness of clamp you assembled to the flat portion of whichever tilt upper you chose.

  13. If you opted for one, insert the bubble level.

  14. If there are any unclear sections of these instructions, any other errors, or if you just have a question please leave a comment!

Tags