1 / 7
Chewing Gum Dispenser – Happy Ramses Edition — image 1
1 / 7

Chewing Gum Dispenser – Happy Ramses Edition

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Got mummy issues? This one guards your candy and rolls his eyes every time you take some. Support-free, no glue.

Rating
5 / 5
Likes
6
Downloads
6
Makes
2
Views
50
Reviews
1

Updated at source:

Model information

License
Standard Digital File License

Meet Happy Ramses. He spent 3,400 years in a pyramid and missed only one thing: candy. Now he’s back, wrapped in his finest linen and guarding your sweets like the treasures of his tomb.

Ramses is a candy and gum dispenser in disguise and the successor to the Chewing Gum Vaults:
Standard Edition & Chic Edition.

Open his mouth and he rolls his eyes down to watch you take a piece of his treasured candy. Yes, he’s counting.

Features:

  • No glue, no screws, no supports

  • Every color is its own print

  • Parts click, peg or twist into place

  • Bandages optional – wrap him as much or as little as you like

  • Ancient curse available on request

Have fun – and keep your fingers away from his savage teeth!

Moving parts

  • Jaw: The head opens on a one-axis hinge and stops at 45°. Pure rotation, no wobble – mummies have stiff joints, not loose ones.

  • Eyes: The hinge rod is locked in the lower part, so the lid turns around it. A link connects the drive pin on the hinge rod to a crank on the eye shaft. As the mouth opens, the eyes roll down. Close the lid and they roll back up.

Candy Container

Ramses’ body is a sleeve with an inner diameter of approx. 55 mm and a height of approx. 80 mm. The container slides in from below. Use either:

  • a standard chewing-gum bottle (see Compatibility), or

  • the printed container (see the Download section)

Fill it with gum, candy or other treasure. Ramses doesn’t judge.

Compatibility

Tested with:

  • Airwaves, 46-piece bottle

  • Wrigley’s Extra, same-size bottle

  • Orbit, same-size bottle

Parts

U | Upper half: 
  • U1 | Lid: Head with upper jaw and eye sockets.

  • U2 | Eyeballs: Four halves that click together around the shaft.

  • U3 | Pupils: Two, one large and one small, pressed into the eyeballs.

  • U4 | Upper teeth: Eight, laid out left to right on the printing plate in mounting order.

  • U5 | Upper gum: Goes into the lid with a short twist and locks like a bayonet.

  • U7a | Hinge rod: Slides through the two closed sleeves of the lower part and cannot turn.

  • U7b | Stop lug: Sits on the flat of the hinge rod next to the right sleeve and stops the lid at 45°.

  • U8 | Skull cap: Sits on the lid with five pegs and holds the eye shaft from above.

  • U9 | Brain: Press-fits into the skull cap from the top.

  • U10 | Eye drive: Eye crank, link, eye shaft, journal sleeve

L | Lower half: 
  • L1 | Lower part: Head base with lower jaw, body sleeve, rib cage, arms and legs.

  • L2 | Lower teeth: Eight, laid out left to right on the printing plate in mounting order.

  • L3 | Lower gum: Pushes straight into the lower jaw and clicks in place.

B | Bandages (optional):
  • B01–B25 | Bandages: Twenty-five numbered pieces of torn linen for the arms, legs and head. Most bands come in two or more pieces that push straight on and peg in place; where bands cross, the upper one pegs through the one below. 3,400 years of wear included.

Materials

  • Filament: PLA (matte recommended)

Print Settings

Setting

Value

Layer height

0.20 mm (0.15 mm eye drive)

Perimeters

2

Supports

None

Infill

5–10 %

Brim

hinge rod, bandage pieces 

Assembly

First check the four assembly sheets. Their numbers match the steps below:

  • Sheet 1 covers steps 1–10 (hinge, eyes, skull cap, brain).

  • Sheet 2 covers steps 11–15 (mouth, bandages, candy).

  • Sheets 3 and 4 (optional bandages) show every bandage piece, numbered B01–B25, with its pegs (black dots) and the holes they go into (rings).

White parts are the ones you add in each step; grey parts are already mounted.

Hinge
  1. Seen from behind, as on sheet 1: (1a) Hold the stop lug (U7b) in the gap just left of the right sleeve of the lower part (L1), flat side down. (1b) Slide the hinge rod (U7a) in from the left, flat side down and drive arm pointing up and back: through the left sleeve, the lug and the right sleeve, until the drive arm touches the left sleeve. Push firmly through the lug – the right sleeve holds it in place. The rod is now locked and cannot turn.

  2. 2a) Press the lid (U1) down onto the rod until its three clips click. (2b) Open and close it once: it should swing freely and stop at about 45°.

Eyes
  1. Press the pupils (U3) into the front eyeball halves (U2).

  2. Slide the journal sleeve onto the eye shaft from the right end, then the eye crank (U10).

  3. Click the eyeball halves together around both ends of the shaft.

  4. Drop the eye unit into the sockets of the lid from above, pupils facing forward.

  5. Press the link down onto the drive pin of the hinge rod (rear hook) and onto the crank (front hook).

  6. (8a) Open the mouth slowly. (8b) The eyes roll down; close it and they roll back up. If they do, Ramses approves.

Head
  1. Press the skull cap (U8) onto the lid until all five pegs connect.

  2. Press the brain (U9) into the skull cap from the top.

Mouth
  1. Press the teeth into the gums in the order they lie on the plate, from left to right: the upper teeth (U4) from below, the lower teeth (L2) from above.

  2. Open the mouth. Push the lower gum (L3) straight into the lower jaw until it clicks. Put the upper gum (U5) into the lid turned slightly off its final position (its four tabs beside their slots), push it up and turn it until it clicks – a short twist, about 12°.

Bandages (optional)
  1. Bandages B01–B13 on the arms and legs (sheet 3), in number order: (13a) arms B01–B10, (13b) legs B11–B13. Push each piece straight on along its dashed line until its pegs sit in the holes. Lower band first: the upper band’s pegs go through the holes in the band below.

  2. Bandages B14–B25 on the head (sheet 4), in number order: (14a) the two bands below the eyes B14–B17, (14b) the three head rings B18–B24, then the strand behind the left ear B25. Every piece goes straight on along its dashed line; each band bridges over the ones below it, so keep the order.

Candy
  1. Slide an Airwaves, Wrigley’s Extra or Orbit bottle (remove the lid first) or the container (Download section) into the body from below until it clicks into place.

Attention: Ramses only guards candy. He doesn’t sanitize it. Keep the container clean and store him away from heat. PLA softens at about 55 °C, and nobody wants a melting mummy...

Tags