1 / 13
Nissan Skyline GT-R R32 – Moving Wheels – 1:18, 1:24 & 1:64 — image 1
1 / 13

Nissan Skyline GT-R R32 – Moving Wheels – 1:18, 1:24 & 1:64

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Nissan Skyline GT-R R32 with rotating wheels, TPU tires and press-fit caps. Includes 1:18, 1:24 and 1:64.

Rating
0 / 5
Likes
3
Downloads
23
Makes
0
Views
110
Reviews
0

Updated at source:

Model information

Category
Vehicles
License
Standard Digital File License

Nissan Skyline GT-R R32 – Moving Wheels

Add the Nissan Skyline GT-R R32 to your collection with this FDM model featuring freely rotating wheels, separate flexible tires and decorative wheel caps.

Available in 1:18, 1:24 and 1:64, the model combines a one-piece body with screw-mounted wheels. Separate parts make it easy to print the body, rims, tires and caps in different colors.

Print and fit checks

The photos and GIFs show a physical R32 prototype and a rolling demonstration.

The additional 1:18 and 1:64 versions have been checked digitally for mesh integrity and assembly clearances. Verify the fit of one wheel assembly with your printer and materials before printing the complete set.

Included files

One ZIP contains three scale folders: 1to18, 1to24 and 1to64.

Each folder includes:

  • Body: one body.

  • Rims x4: four rims in one STL.

  • Tires x4: four tires in one STL.

  • Caps x4: four wheel caps in one STL.

12 STL files in total, plus printing and assembly instructions.

Example filename: Nissan Skyline GT-R R32 Body 1to24.stl

Model features

  • Freely rotating wheels mounted with individual screws.

  • One-piece body with closed doors, hood and trunk.

  • Closed, flat underside with a beveled rear floor.

  • Separate tires designed for TPU 85A.

  • Retaining lips on both sides of each rim, with matching tire recesses.

  • Recessed screw heads covered by press-fit caps.

  • Tires and caps designed for assembly without glue.

  • Scale-specific screw sizes, clearances and wheel interfaces.

  • Reinforced and simplified wheel details in the smallest scale.

Required screws

You need four screws per model.

Scale

Approximate model length

Screws

Maximum screw-head diameter × height

1:18

252.5 mm

4 × M3 × 16 mm

Ø5.6 × 3.0 mm

1:24

189.4 mm

4 × M2 × 10 mm

Ø4.0 × 2.0 mm

1:64

71.0 mm

4 × M1.6 × 6 mm

Ø3.0 × 1.6 mm

Choose screw heads within these dimensions so they sit below the caps.

Print the supplied files at 100% scale. Use the dedicated folder for each scale, as the screw holes and fitting clearances are adjusted separately.

Wheel assembly

  1. Remove supports and any first-layer brim from the parts. Clean the backs of the hubs and the screw and cap seats.

  2. Stretch each TPU tire over the retaining lip and seat it in the matching recesses.

  3. Attach each rim to the body using the correct screw.

  4. Adjust the screw tension until the wheel rotates freely with a small amount of axial play. Avoid clamping the wheel against the mounting sleeve.

  5. Check the rotation, then press the cap into place until its flange rests against the front of the rim.

Recommended print orientation

  • Body: flat underside on the build plate. Use local supports where needed beneath wheel arches, mounting-sleeve ends, bumpers, mirrors and other overhangs.

  • Rims: inner side on the build plate, decorative face upward. Add local supports beneath the recessed hubs while keeping the screw and cap sockets clear.

  • Tires: flat sidewall on the build plate.

  • Caps: flat back on the build plate, decorative face upward.

Suggested FDM settings

  • Body, rims and caps: PLA or PETG.

  • Tires: TPU 85A.

  • 1:18 and 1:24: a 0.4 mm nozzle with approximately 0.12–0.20 mm layers is a suitable starting point.

  • 1:64: a 0.25 mm nozzle and 0.08–0.12 mm layers are recommended for the small rims and caps.

  • Use a proven profile for your filament and inspect the supports, bridges and small walls in the slicer before printing.

Tags