1 / 7
Quiver set for pens, files and brushes to fit Systainer³ M and L – Ø 8 to 30 mm, one tile — image 1
1 / 7

Quiver set for pens, files and brushes to fit Systainer³ M and L – Ø 8 to 30 mm, one tile

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Quiver set for pens, files and brushes, diameter 8 to 30 mm, one tile for Systainer M and L.

Rating
0 / 5
Likes
0
Downloads
0
Makes
0
Views
4
Reviews
0

Updated at source:

Model information

Category
Organizers
License
Creative Commons — Attribution — Noncommercial

16 quivers per M tile from Ø 8 to 30 mm; pens, files and brushes stand upright.

Fits: Systainer³ M and L cases; inside dimensions from the manufacturer's price list. Not an accessory by TANOS or Festool and not affiliated with them; “Systainer³” and “Sortainer³” are named only to describe what the part fits. No logos and no lettering on the parts.

Please note: nothing of this design has been printed yet, and it has not been tested in a case. Some dimensions are estimates (details under “Dimensions”), and corner radius and floor profile of the cases are not published. Print the free fit sample set (in our “Magmacode” profile) first.

For everything long and round: scribers, pens, files, brushes. Each quiver is 25 mm deep; the tool stands on a narrow ring. The diameters are a series, not a standard.

  • Diameters: 8, 10, 12, 14, 16, 20, 25, 30 mm (+ 0.5 mm), each size 2 × on the M tile (16 quivers), 2 × on the L tile (16).

  • Height: tile 40 mm. Tools stand 25 mm deep: 150 mm pens fits from M 237 (not in M 112, M 137 and M 187), 250 mm files fits from M 337 (not in M 112, M 137, M 187 and M 237).

Variants and installation: Single tile: fits any of the 4 places in the Systainer³ M; R 15 corners towards the case wall, turned by 180° in the back row. Can be mixed with other tiles of the same size. Single tile: fits any of the 6 places in the Systainer³ L; R 15 corners towards the case wall, turned by 180° in the back row. Can be mixed with other tiles of the same size.

Dimensions: Inside dimensions taken from the TANOS price list 2026; our part has not been tested in the case yet. Systainer³ M: 2 × 2 tiles of 193.6 × 136.3 mm (inside 389.5 × 275 mm), 2 connector bars; Systainer³ L: 3 × 2 tiles of 166.3 × 136.4 mm (inside 501.5 × 275.2 mm), 3 connector bars. The diameter series is a selection, not a standard (estimate). The corner radius, floor profile (floor cross, radius between floor and wall) and wall draft of the cases are not published. That is why we relieve generously: R 15 in the case corner, a 4 mm chamfer at the bottom edge, a hollow underside with a rim (a floor cross up to 5 mm high stays clear) and 1.0 mm clearance per side to the case, 0.3 mm between tiles. Print the free fit sample set (in our “Magmacode” profile) first: it shows on your own case whether corner, floor edge and clearance work.

Material: PETG recommended, because a tool case quickly ends up in a car or in the sun. PLA works too, but it deforms in a hot car or in the sun.

Variants (all included)

  • Single tile M

  • Single tile L

Print settings

  • Material: PETG (or PLA). PETG recommended: a tool case quickly ends up in a car or in the sun, and PLA deforms in the heat.

  • Layer height 0.2 mm, 3 walls, 15 % infill, no supports.

  • Orientation: Tiles upside down, top face on the bed; connector bars flat. No supports.

  • Print one tile first and try it in the case, then the rest of the set.

  • Print time approx. 8 h 10 min and about 154 g (default variant Single tile M: quiver tile; other variants differ).

Assembly

  1. Put the tiles in with the R 15 corners towards the case wall, the back row turned by 180°.

  2. At the joint between the front and the back row, lay one connector bar per column into the two half pockets.

Safety

Organiser insert, nothing load-bearing. Made to fit Systainer³ and Sortainer³ (inside dimensions per the manufacturer's price list); not an accessory of TANOS or Festool, no affiliation with them.

Fit

If a quiver is too narrow, use the next larger one; do not scale the tile.

FAQ

Have you printed the part and tested it in a case? Not yet. Inside dimensions taken from the TANOS price list 2026; our part has not been tested in the case yet; the tool dimensions come from the standards named. That is why you should print the free fit sample set and a single tile first.

What are the connector bars for? A flat bar (30 × 5 × 2 mm) sits in two pockets at the joint between the front and the back tile and keeps them in line without clamping. Lengthwise the case walls hold the tiles. You can also leave the bars out.

Is this an accessory by TANOS or Festool? No. The parts are made to fit Systainer³/Sortainer³, not an accessory by TANOS or Festool, no affiliation with them. We name products only to describe the fit.

Which material? PETG recommended, because a tool case quickly ends up in a car or in the sun. PLA works too, but it deforms in a hot car or in the sun.

How it's made

Parametric CAD (build123d, Python), exact solids. The CAD code was written with an AI assistant and checked by us; no AI-generated meshes or images. Renders are made from the CAD in Blender and show the part in simple staged scenes (placeholder case without brand, cutting mat); they are not photos.

License

CC BY-NC 4.0: you may share and adapt it for non-commercial purposes, as long as you credit Magmacode and link the license (https://creativecommons.org/licenses/by-nc/4.0/). Commercial sale of printed parts only by written agreement with Magmacode.

Matching tool case inserts (bit holders, drill cassettes, drawer inserts and more) are in the Magmacode profile.

Tags