Mini Rack 10" – Side Rail remix para barras de rack en L genéricas (M4)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Remake del side_rail_long del modelo “Mini Rack 10” server rack for NavePoint or Gator Rackworks rails” de StreelyDan. L
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 1
- Makes
- 0
- Views
- 11
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Electronics
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Remake del side_rail_long del modelo “Mini Rack 10” server rack for NavePoint or Gator Rackworks rails” de StreelyDan. Lo he adaptado a barras de rack metálicas en L genéricas, que no son ni NavePoint ni Gator. Estas barras no encajaban en el diseño original porque los agujeros no coincidían con las ranuras. Gracias a StreelyDan por el diseño original.
Cambios respecto al original
Los agujeros de fijación se han movido para que coincidan con las ranuras de la barra. El primero empieza a 20 mm del tope donde apoya la barra y el segundo a 42 mm.
Los agujeros llevan rosca M4 directa en la pieza, sin tuercas.
La placa es 4 mm más larga, para que los dos tornillos tengan material de sobra alrededor.
El reborde trasero llega 3 mm más hacia los agujeros. Así la barra apoya de lado contra él y no queda hueco.
Los cambios están aplicados en los dos extremos del rail.
Barra utilizada
Barras de rack metálicas compradas en Amazon: https://www.amazon.es/dp/B00LFSBL6S
Perfil en L. El ala atornillada mide 29 mm de ancho y la otra queda libre para las bandejas.
Ranuras ovaladas de 7 × 9 mm, con unos 20,3 mm de paso.
Una vez montada, el centro de los agujeros queda a 14,5 mm del borde de la barra.
Archivos incluidos
side_rail_long_M4_v13.3mf: la pieza completa.test_piece_v13.3mf: pieza de prueba de 4,6 mm de grosor. Se imprime en pocos minutos y sirve para comprobar que tu barra encaja antes de imprimir la pieza entera.dibujo_acotado_v13.png: croquis acotado con todas las medidas.
Impresión recomendada
Material: PETG (también vale PLA).
Perímetros: 4–5.
Capas superiores e inferiores: 5.
Relleno: mínimo 15–20 %, gyroid o cúbico.
Soportes: no hacen falta.
Montaje
Tornillos M4 roscados directamente en el plástico. No aprietes en exceso.
La barra apoya en el tope del pie y de lado contra el reborde.
El resto de piezas del minirack original (cross_rail, etc.) siguen siendo compatibles.
Antes de imprimir
Si tu barra tiene otras medidas, imprime antes la pieza de prueba y compárala con el croquis.
Remix of side_rail_long from “Mini Rack 10” server rack for NavePoint or Gator Rackworks rails” by StreelyDan. I adapted it to generic L-shaped metal rack rails, not NavePoint or Gator. These rails didn’t fit the original design because the mounting holes didn’t line up with the slots. Thanks to StreelyDan for the original design.
Changes from the original
The mounting holes have been moved to line up with the rail slots. The first one starts 20 mm from the rail end stop and the second at 42 mm.
The holes are M4, threaded directly into the part, with no nuts needed.
The plate is 4 mm longer, so both screws have plenty of material around them.
The rear lip reaches 3 mm further toward the holes. This way the rail rests against it sideways with no gap.
The changes are applied on both ends of the rail.
Rail used
Metal rack rails bought on Amazon: https://www.amazon.es/dp/B00LFSBL6S
L profile. The screwed leg is 29 mm wide and the other leg stays free for shelves.
Oval slots of 7 × 9 mm, about 20.3 mm pitch.
Once mounted, the hole centres sit 14.5 mm from the rail edge.
Included files
side_rail_long_M4_v13.3mf: the full part.test_piece_v13.3mf: a 4.6 mm thin test piece. It prints in a few minutes and lets you check that your rail fits before printing the whole part.dibujo_acotado_v13.png: dimensioned drawing with all measurements.
Recommended print settings
Material: PETG (PLA works too).
Perimeters: 4–5.
Top and bottom layers: 5.
Infill: at least 15–20 %, gyroid or cubic.
Supports: not needed.
Assembly
M4 screws thread straight into the plastic. Don’t overtighten.
The rail rests on the foot stop and sideways against the lip.
The other parts of the original mini rack (cross_rail, etc.) remain compatible.
Before printing
If your rail has different dimensions, print the test piece first and compare it with the drawing.