1 / 6
COOAU CU-SPC03 4K Travel Case | Smooth R12 | MMU3 — image 1
1 / 6

COOAU CU-SPC03 4K Travel Case | Smooth R12 | MMU3

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Fitted camera-kit case for a CU-SPC03, five batteries, charger and cable. Smooth R12 shell with flush MMU lettering.

Rating
0 / 5
Likes
0
Downloads
1
Makes
0
Views
22
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

Keep a COOAU CU-SPC03 camera, five batteries, the charger and a USB cable together in one fitted, filament-hinged case.

This IMAGE × TITUS project was developed around a real camera kit and revised after hands-on feedback. R12 keeps the fitted interior, removes the exterior ribs and gives the fixed hinge-pin holes a small clearance increase. The lid lettering and internal revision mark are flush two-color inlays.

Before printing: The previous case was physically tested and the contents fit. R12 has passed digital geometry and slicer checks, but its revised pin fit and smooth-shell comfort have not been physically tested. Print the included pin-clearance coupon first.

What it holds

- One bare COOAU CU-SPC03 4K touchscreen action camera, without its waterproof housing.

- Five separate battery slots.

- One charger matching the measured kit.

- One USB cable in the open cable compartment.

Finger reliefs help you lift the contents out. The rear hinge and separate front latch use ordinary 1.75 mm filament as pins. No metal hinge hardware is required.

This is a fitted case for the listed kit, not a universal action-camera box. Check your charger and battery dimensions before printing. The main shell footprint is 132 × 100 mm; the closed shell is 50 mm high. Hinges and latch extend beyond that footprint.

What changed in R12

- Removed all 32 exterior ribs, leaving smooth side walls.

- Increased the fixed rear-hinge and front-latch bores from 1.75 to 1.85 mm nominal.

- Kept the moving bores at 2.25 mm.

- Preserved the fitted pockets, hinge axes, latch, alignment tongue and 0.8 mm flush inlays.

- Updated the revision marking to R12.

Printed horizontal holes vary with material, tuning and support cleanup. The comparison coupon includes both rear and front samples at 1.80, 1.85 and 1.90 mm. Choose the smallest size that accepts your actual filament pin comfortably while retaining it. The supplied full-case files use 1.85 mm.

Files and print setup

The download includes eight STL meshes, two model-only MMU 3MFs, six configured PrusaSlicer projects, editable OpenSCAD source with its dependencies, CAD previews and an assembly guide.

Configured projects use:

- Original Prusa MK4S + MMU3, 0.4 mm high-flow nozzle.

- Generic PLA, 0.20 mm layers.

- Three perimeters and 15% gyroid infill.

- Six bottom and five top solid layers.

- A 5 mm brim and build-plate-only snug supports.

- MMU slot 1: black case bodies. Slot 2: gray lettering.

- A wipe tower for the base and lid; none for the single-color parts.

Print the base and lid separately in the saved orientations. Keep each body and its inlay together as one multipart object. Do not auto-arrange the letters separately. For a single-color print, assign both volumes to the same extruder and reslice with your printer's profile.

The saved projects were test-sliced in PrusaSlicer 2.9.7. Check your actual printer, nozzle, loaded materials, supports and toolpaths before printing. The package intentionally contains no ready-to-run G-code.

Slicer estimates

- Base: 2 h 43 min, 118.72 g.

- Lid: 1 h 35 min, 63.32 g.

- Latch: 6 min, 2.11 g.

- Pin-clearance coupon: 34 min, 9.95 g.

The three main parts total about 4 h 25 min and 184.15 g, including the saved support and purge estimates. These are slicer estimates, not measured print results.

Assembly and fit checks

1. Print the clearance coupon first, then check the same 1.75 mm filament you will use for both pins.

2. Print the case parts. Let them cool fully, then remove the brim and supports carefully.

3. Align the rear knuckles and gently feed the filament pin through the hinge. Do not force a tight pin or split a knuckle.

4. Fit the front latch to the lid's pivot and insert its filament pin. Trim the pins so no sharp ends protrude.

5. Check free hinge movement, latch engagement and pin retention.

6. Insert the kit and close the lid gently. Confirm that the lens, screen and batteries are not compressed.

For a different coupon result, adjust the appropriate fixed-bore parameter in the source and re-export before printing a full case.

Limits and image notes

This is an organizer for normal storage and hand carrying. It is not waterproof, drop-tested, crush-rated or a certified battery transport container. PLA can soften in a hot vehicle. Do not store damaged or swollen batteries, and do not charge batteries inside the closed case.

R12's digital checks passed watertight-mesh, sampled opening-clearance and MK4S/MMU3 slicing checks. They do not establish physical durability, pin retention, fatigue or fit on another printer.

The gallery contains CAD and toolpath views of the actual R12 files, not photographs or proof of a successful physical print. Use these views and the files as the dimensional reference.

Attribution and license

Design project: IMAGE × TITUS / Image36.

Rugged styling and filament-pinned hinge/latch architecture were informed by “Rugged Box, Parametric/Customizable, No Hardware” by Baldrick9:

https://www.printables.com/model/1489229-rugged-box-parametriccustomizable-no-hardware

The COOAU geometry was independently constructed around the fitted camera kit; no source geometry from that listing was imported. Attribution and the source project's noncommercial/share-alike boundary are retained.

Additional hinge design references:

- BOSL2 hinges.scad, BSD 2-Clause: https://github.com/BelfrySCAD/BOSL2/blob/master/hinges.scad

- morganp OpenSCAD_hinge: https://github.com/morganp/OpenSCAD_hinge/blob/main/hinge_library.scad. Dimensional reference only; no code or geometry copied.

This release is shared under Creative Commons Attribution–NonCommercial–ShareAlike 4.0 International (CC BY-NC-SA 4.0). Credit the project and its sources, keep derivatives under the same license, and do not sell the files or printed derivatives without the necessary permissions.

COOAU is referenced only to identify compatibility. This is an independent community project.

Tags