LayersFactory
Report model
1 / 5
BTicino Sfera New rain shield, 2 modules (350521 replica) — image 1
1 / 5

BTicino Sfera New rain shield, 2 modules (350521 replica)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

FerelArg

FerelArg

@multimake_570804

Rain shield for 2-module BTicino Sfera New entrance panels. Replica of ref. 350521. Prints flat, no supports.

Rating
0 / 5
Likes
0
Downloads
0
Makes
0
Views
3
Reviews
0

Updated at source:

Model information

Source
Printables
Category
Other House Equipment
License
Creative Commons — Attribution — Noncommercial — Share Alike
DetailsFiles (1)Makes & comments (Makes: 0) (Comments: 0)Remixes (0)Collections (0)Related

ENGLISH

Printable rain shield for BTicino Sfera New 2-module entrance panels (audio and video door entry). It copies the shape and outer size of the original 2-module rain shield, ref. 350521, and sits between the wall and the front frame (ref. 350221).

My flush-mounted panel had no cover at all and the audio module misbehaved whenever it rained. The shield is now printed and installed, as you can see in the photos.

Dimensions

  • Overall: 146 × 239.5 × 38 mm, same as the official part

  • Side wings: 38 mm deep at the top, tapering to 21 mm at the bottom

  • Back plate 2 mm, walls 2.4 mm

  • Central opening: 92 × 185 mm

The outer dimensions come from the official BTicino data sheet. Check the opening against your own frame before printing.

Printing

  • Orientation: back plate flat on the bed, no supports needed

  • Material: ASA for outdoor use, because it resists UV and heat. PETG is fine in the shade

  • Suggested settings: 0.2 mm layers, 4 walls, 20 % infill

  • Footprint is 146 × 240 mm, so the bed needs at least 240 mm on one axis

Mounting

  1. Remove the front frame of the panel.

  2. Place the rain shield against the wall, around the flush-mounted box.

  3. Refit the frame on top so it clamps the shield.

  4. Seal the top and both sides against the wall with neutral silicone. Leave the bottom edge open so water can drain.

Modelled in build123d with AI assistance. Not affiliated with BTicino or Legrand. All trademarks belong to their owners.

ESPAÑOL

Visera antilluvia imprimible para placas de calle BTicino Sfera New de 2 módulos (portero y videoportero). Copia la forma y las medidas exteriores de la visera original de 2 módulos, ref. 350521, y va montada entre la pared y el marco frontal (ref. 350221).

Mi placa empotrada no tenía ninguna protección y el módulo de audio fallaba cada vez que llovía. La visera ya está impresa e instalada, como se ve en las fotos.

Medidas

  • Totales: 146 × 239,5 × 38 mm, las mismas que la pieza oficial

  • Alas laterales: 38 mm de fondo arriba, bajando a 21 mm en la parte inferior

  • Placa trasera de 2 mm, paredes de 2,4 mm

  • Hueco central: 92 × 185 mm

Las medidas exteriores salen de la ficha oficial de BTicino. Comprueba el hueco con tu marco antes de imprimir.

Impresión

  • Orientación: placa trasera apoyada en la cama, sin soportes

  • Material: ASA para exterior, porque aguanta el sol y el calor. PETG vale si está a la sombra

  • Ajustes sugeridos: capas de 0,2 mm, 4 perímetros, 20 % de relleno

  • Ocupa 146 × 240 mm, así que la cama necesita al menos 240 mm en un eje

Montaje

  1. Quita el marco frontal de la placa.

  2. Coloca la visera contra la pared, alrededor de la caja de empotrar.

  3. Vuelve a montar el marco encima para que sujete la visera.

  4. Sella la parte de arriba y los dos lados contra la pared con silicona neutra. Deja el borde inferior abierto para que el agua escurra.

Modelada en build123d con ayuda de IA. Sin relación con BTicino ni Legrand. Las marcas pertenecen a sus propietarios.

Tags

doorbellrainvisorbticinointercomlegrandsferarainshieldporterovideoportero