1 / 3
Edge clamp fit test S/M/L and keder test strips – camper organizers, free — image 1
1 / 3

Edge clamp fit test S/M/L and keder test strips – camper organizers, free

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Free camper fit test: three short edge clamps and four keder test strips show which size fits your furniture and rail.

Rating
0 / 5
Likes
0
Downloads
0
Makes
0
Views
2
Reviews
0

Updated at source:

Model information

Category
Test Models
License
Creative Commons — Attribution

Free fit test for the camper: three short edge clamps show on your own furniture board which size sits; four keder test strips show which head and neck fit your keder rail.

Fits: Furniture boards 11–20 mm thick and free keder rails in campervans, motorhomes and caravans; checks the fit before you print hooks, holders or clips. Not an accessory of any vehicle, furniture or awning manufacturer and not affiliated with one; no brand names, no logos on the parts.

Before you print hooks, cup holder, tray or keder clips: this plate settles the two dimensions that are not reliably documented in public, on your own vehicle.

  • Three short edge clamps S, M, L (10 mm wide, otherwise like the products), size as 1–3 dots on top of the bridge. S for boards 11–14 mm (nominal 12/13 mm); M for boards 14–17 mm (nominal 15/16 mm); L for boards 17–20 mm (nominal 18/19 mm).

  • Four keder test strips, one per neck width 2.0 / 2.5 / 3.0 / 3.5 mm (1–4 dots on top), each with head steps 7.5 to 5.5 mm (1–5 dots at each step). Slide it in from the open end of the rail: it goes in as far as the head fits.

  • How to read the strips: the right strip slides easily without slipping out through the slot. Our keder clips come with head/neck 5.5/2.0 (small), 6.5/3.5 (medium) and 7.5/3.0 mm (large).

  • Free, licence CC BY 4.0. The short clamps are test parts, not holders.

Dimensions: Board thicknesses: tolerances to EN 315 according to a manufacturer page (12 mm +0.6/−0.8, 15 and 18 mm +0.7/−0.9), retailers state ±1 to ±2 mm, decor and HPL boards are not documented. Hence sizes with ranges instead of nominal sizes. Measure the board thickness with a caliper, then choose the size. The free keder test strips (in our “Magmacode” profile) show beforehand which size fits your rail. Calculated, not printed yet.

Load: No load: the fit test is only for trying; spring travel calculated, not tested in a vehicle. Do not leave anything heavy on it while driving; stow loose items securely.

Edges: Edges you touch are rounded R 3.2 mm; only the side that lies on the print bed has a small chamfer (0.6 mm).

Material: PETG as the standard, ASA as an alternative. No PLA: a parked vehicle gets 60 to 70 °C inside in summer, PLA then softens.

For light items only, in the interior and on a free keder rail. No load securing, nothing load-bearing, nothing on gas, water, heating or electrical parts. Secure loose items safely while driving. The vehicle gets hot in summer: PETG or ASA, not PLA.

Print settings

  • Material: PETG (or ASA). No PLA: a parked vehicle gets very hot inside in summer, and PLA then softens and deforms under load.

  • Layer height 0.2 mm, 4 walls, 25 % infill, no supports.

  • Orientation: As the files are laid out, no supports: clamps flat on their side, keder test strips standing (40 mm high).

  • Print time approx. 3 h 17 min and about 57 g (complete part).

Safety

For light items only, in the interior and on a free keder rail. No load securing, nothing load-bearing, nothing on gas, water, heating or electrical parts. Secure loose items safely while driving. The vehicle gets hot in summer: PETG or ASA, not PLA. Do not leave anything heavy on it while driving; stow loose items securely.

FAQ

Have you printed the part yet? Not yet. Calculated, not printed yet: dimensions, spring travel and loads are calculated, the part is not tested in a vehicle. That is exactly what the fit test is for: it is the first thing you print. Which size do I need? Measure the board thickness with a caliper, then choose the size. S for boards 11–14 mm (nominal 12/13 mm); M for boards 14–17 mm (nominal 15/16 mm); L for boards 17–20 mm (nominal 18/19 mm). If your board is exactly on a limit (14 or 17 mm), both sizes fit; the smaller one holds tighter. Which material? PETG as the standard, ASA as an alternative. No PLA: a parked vehicle gets 60 to 70 °C inside in summer, PLA then softens. May I screw the clamp to the vehicle wall? No. Optionally, a 3 × 16 mm wood screw (countersunk) through the hole in the rear jaw fixes the clamp permanently: into the furniture board only, never into the vehicle wall or sheet metal. The tip reaches about 9.5 mm deep, so only for boards from 11 mm.

How it's made

Parametric CAD (build123d, Python), exact solids. The CAD code was written with an AI assistant and checked by us; no AI-generated meshes or images. Renders are made from the CAD in Blender; they are not photos.

License

CC BY 4.0: you may share and adapt it, also commercially, as long as you credit Magmacode and link the license (https://creativecommons.org/licenses/by/4.0/).

Matching edge clamp hooks, cup holders, trays and keder clips for campervans and caravans are in the Magmacode profile.

Tags