1 / 11
Bag Clip with Snap Latch, 4 Sizes, Print-in-Place — image 1
1 / 11

Bag Clip with Snap Latch, 4 Sizes, Print-in-Place

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Strong hinged bag clip with a spring latch in 62, 92, 122 and 162 mm. Prints in one piece, flat, no supports.

Rating
0 / 5
Likes
1
Downloads
5
Makes
0
Views
12
Reviews
0

Updated at source:

Model information

Category
Kitchen
License
Creative Commons — Attribution — Noncommercial — Share Alike

A sturdy bag clip with a hinged arm and a spring latch. Squeeze it until it clicks, and it stays shut. To open it, push the thumb tab outward with your thumb. A V-shaped ridge on one arm presses the bag into a matching groove in the other arm, so the clip holds gathered bags as well as a flat folded pouch.

Everything prints in one piece, hinge included. No supports, no assembly, no hardware.

FOUR SIZES

S: overall length 62 mm, clamping length 43 mm, height 10 mm

M: overall length 92 mm, clamping length 73 mm, height 10 mm

L: overall length 122 mm, clamping length 103 mm, height 12 mm

XL: overall length 162 mm, clamping length 143 mm, height 12 mm

Clamping length is the usable jaw length for the bag opening. The dimension drawings (PDF) show every size with all main measurements.

HOW TO USE

1. Lay the bag opening between the arms. You can gather it or fold it flat.

2. Squeeze the arms together until the latch clicks.

3. To open, push the thumb tab at the latch outward. The arm swings free.

PRINTING

Print flat, exactly as oriented in the files. No supports.

Print-in-place hinge with 0.35 mm clearance. It should turn straight off the plate. If it feels stiff, open and close it a few times.

Our settings: 0.4 mm nozzle, matte PLA, 0.20 mm layers, 4 walls, 20 % grid infill, 5 top and 3 bottom layers, textured PEI plate.

All four sizes fit on one 256 x 256 mm plate. That plate took about 1 h 40 min on our printer, with an estimated filament use of 68.5 g.

WHAT IT FITS

Fits: chip and snack bags, bread and crouton bags, coffee bags, spice pouches, paper and foil pouches. We tested it on a bag of bread cubes and on spice pouches.

Gathered film up to about 1.2 mm thick. This is a calculated design value, not a tested limit. Much thicker bundles keep the latch from closing.

Does not fit: rigid boxes, very thick multi-layer bags.

Freezer: not tested. PLA can become brittle in the cold. For the freezer, PETG is likely the better choice, but we have not tested it.

FILES

STL per size, print-ready (both arms in print position). STEP per size (solids built from the print mesh, faceted). Dimension drawings for all four sizes (PDF).

LICENSE

CC BY-NC-SA 4.0. Remixes are welcome, please keep the license and do not sell prints or files.

KURZFASSUNG (DEUTSCH)

Stabiler Beutelclip mit Gelenk und Schnappverschluss in vier Größen: S 62 mm, M 92 mm, L 122 mm, XL 162 mm. Zudrücken, bis es klickt. Zum Öffnen die Daumenlasche am Haken nach außen drücken. Eine V-Leiste presst den Beutel in eine V-Nut; dadurch hält der Clip geraffte Beutel und flach gefaltete Packungen.

Wird in einem Stück gedruckt, samt Gelenk, flach und ohne Stützen. Unsere Einstellungen: 0,4-mm-Düse, PLA matt, 0,20-mm-Schichthöhe, 4 Wände, 20 % Infill. Alle vier Größen passen auf eine Platte. Der Druck brauchte bei uns etwa 1 h 40 min; der berechnete Materialverbrauch beträgt 68,5 g.

Passt für Chips-, Brot-, Kaffee- und Gewürzbeutel. Die Angabe „bis etwa 1,2 mm geraffte Folie“ ist ein berechneter Konstruktionswert, keine getestete Grenze. Nicht für starre Schachteln. Im Tiefkühler nicht getestet; PLA kann in der Kälte spröde werden.

Lizenz CC BY-NC-SA 4.0.

Tags