Solar System / Moon 205mm adapted E27 Base for the dark side of the moon
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Enables the Moon Model to be not only a full moon
- Rating
- 0 / 5
- Likes
- 5
- Downloads
- 13
- Makes
- 0
- Views
- 73
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Art & Designs
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Hello everyone,
well, since I am using the solar system models quite extensively in different sizes for myself and gifts for friends - preferably the moon, there was the idea that, well the moon, it differs from how we see the moon on a daily basis.
So I did a little bit of begginers CAD to build myself some parts that enable the moon to be either full, half, or everything between half and a new moon (lamp powered off).
Please consider that as a work in progress - I printed it for two moons at the moment and I am quite happy with the result.
BOM:
10* 6x3 mm Magnets
41 mm of 3 mm (diameter) wire
a piece of filament
Printing advice:
I printed everything out of ASA since even LED bulbs can get a little bit too hot for PETG or PLA to hold up. Thats why the adapted E27 puck base and the original puck base lid should be scaled to something like 100.8% when printing with ASA (i otherwise had problems to properly fit in the E27 holder).
All the other parts are designed to print with ASA, so please do not compensate the shrinkage if possible.
Cover right and cover left should be printed laying flat - one of them needs then a whole lot of support, I found no other way.
Building advice:
The 3 mm hole in the Puck base is accessible from the top and should be drilled all the way through so that your wire can spin freely in it.
Take a file to file down the wires ends to achieve some flat spots that fit the gears. The inner gear can be pressfit onto the wire, at least in my case that was enough to grip through the applied torque. The bottom one needs to be filed so that you can slip it in, when doing the assembly.
The Cover Right/Cover left should be attached to each other by threading a piece of filament through the hole - melt the top and bottom part of it and press in the direction of the model with some cold steel - that should be a smooth hinge, use some fine sandpaper to grind the hinge a little bit flat while moving it until it runs smooth.
Insert the magnets in the 4 spots of the cover - with alternating polarities in between the sides (necessary for assembly!!). The top magnets polarisation is not important. As long as it fits to its counterpart on the outer sphere.
Drill the top holes of the inner sphere and outer sphere out until you can fit a piece of filament in there as well to create a swivel point. Insert the magnets accordingly, so that the closed "cover" pieces magnetize to the sides of the spheres that also close the lamp access.
With a little bit of sandpaper smooth the bottom of the outer sphere as well as possible, same for the inner-base, smooth the top of that model - this is the interface where your model will slip on each other. I applied a drop of fluid-film oil to increase slipperyness.
To finish the inner assembly: Slide the inner sphere into the outer sphere so that the open half-spheres are opposite to each other (i hope that is clear), than you need to flex them only a little bit to bring them to each other. (There might be an example picture added if necessary)
The inner-base fits only in ONE space onto the inner sphere - with the small hole in the base turned 90 degree to the magnet side of the inner sphere clockwise. You can fix that assembly to each other with a little bit of epoxy if needed.
Now you can also slide in your piece of wire with the inner gear pressfitted to the top of it. Make sure that the holes in the base and the puck base are big enough and well aligned.
With the bulb already inserted in the spheres you can now assemble the puck base as usual - and thread on the bulb with all of the additional stuff. The last thing is to press the wire onto the know when passing through the puck. Done. The original puck lid needs a little bit of shaving off of the plastic to fit - but thats nothing an exacto knive can't do :)
Test if the mechanism is working as wished by turning the know. Attach the magnetized covers outside of the planet to check if everything is fine. If so. just insert the folded cover into the moon-model. Screw on the base as usual and now carefully shake and turn the whole moon until you hear and see the magnets snap onto the spheres as they should. It helps to do this with the light turned on.
Have fun! And help to improve the mechanism/fitting.
If you want to use the moon as normal there are two option - option 1, just dont use the cover, depending on your printed moon the diffusion is diffusive enough in the print that the moon is fully illuminated. Option 2, unscrew the inner spheres from your puck base.
Known Problems:
The inner gear is a little bit too close to the planet rim, which makes screwing it all together not that easy (improved version is printing at the moment)
One side of the covers does not fit perfectly and leaves a light-slit (nice to have but not necessary for the wished effect)
it cannot be closed 100% (I would have a solution but then the 180 degree opening would not be possible - it is only like an ~8 degree slit, I think thats alright)
it cannot be opened more than 50% (dark side of the moon - this is kind of by design)
Puck base adaption is not great (i am just printing an improved version) + no adaption to the lid (uploaded in V2).
Puck base and puck lid need to be scaled to 10% (10.08% x, 10.08% y, 10% z) for printing
Changelog V2:
added modified puck lid
modified puck base for throughhole - correctly positioned
adjusted hole position on inner base
inner base and inner sphere do not align anymore - don't use atm
new interlocking geometry - but I think it must be glued.
v2 version of everything of the moving mechanism