Fenix Flashlight holder for my RV
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
The Fenix UC35 is my "go to" flashlight for camping, I didn't like losing it on my night stand so I made a holder for it
- Rating
- 0 / 5
- Likes
- 19
- Downloads
- 75
- Makes
- 1
- Views
- 612
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Gadgets
- License
- Creative Commons — Attribution
My go to flashlight when I'm camping is the Fenix UC35.
What I like about it is that you can make it really bright or, when it is really dark, just a light bit bright (moonlight mode, 1 lumen) so you can look around for something in your camper without disturbing your partner who is sleeping.
The downside of camping when it is really dark is, you need your flashlight to find your flashlight! I was trying to put it in the same place on the shelf next to the bed but it would move, or I would move it when something else was put there, and then I'd be rummaging around for it and that was noisy. I decided what I really needed was a holder for it that I could mount to the side of the cabinet which put it always in the same place. It also meant that there was no chance of putting something else down that would move it out of the way. This is the result.
Design Discussion
As you can see from the model file this is version 4b 😀. So lets discuss some of the design details that may not be obvious.
First, I have printed this in PLA. It could have been PETG but PLA works fine. In one of the pictures you can see the dimensions for the extrusion I used to make the 'grip'.
The thickness of the wall in this grip determines how flexible the gripper is and how tightly it holds the flashlight. Making it 2mm thick using PLA would hold it, but after a while from putting the light in and taking it out, it got to the point where it would sometimes drop it. Making the wall 4mm thick made the grip really strong. So strong that I couldn't easily remove the light once I had put it in. 3mm seems to be a good place for it using PLA.
Since this is in my trailer (caravan) and may be holding the flashlight while we're driving, I wanted it to be grippy enough that it wouldn't fall out if we hit a bump.
The second design issue was attaching it to the flashlight. This particular flashlight has two 2mm grooves that run along its sides and the ‘nubs’ on the gripper latch into those. Not all flashlights do of course and so if you're remixing this make sure to remove those if your flash light is simply knurled without the grooves. Also the 23mm diameter is pretty standard for flashlights based on the 18650 LiOn cell but you should measure when you make it to be sure.
You may also notice that it goes slightly “past” a half circle. This is so that the arms reach around the flashlight to hold it. Going more than about 10 degrees (which is what I used) means the sides of the gripper have to push apart more to let the flash light in (you can't drop it from the top with this flashlight since the base with the push button on/off switch is not the same diameter all the way down. And that brings up the third design issue.
You will notice that the light body is tilted away from the wall. The third design issue was that I was thinking you could drop the light in from the top, and it would slide down at an angle until it “hit” the wall which would support it in the holder. This was changed to the push in and pull out design in the final version. I left the tilt in however since it allows this like to be used in the mounted position as something of a reading light, reflecting indirectly off the top of the camper above your head. With this light on full brightness, it is a lot of light. In moonlight mode it gives you plenty of light to see what you're doing without being too obnoxious.
Finally there is “attaching it to the wall.”
This camper, like many campers, use a very thin Luan style board for the interior cabinetry. This saves weight and the cabinets are not structural so they don't have to be that strong. And initially I made the wall side of this mount flat and used 3M VHB tape to attach it to the wall. Even with about 125 sq mm it didn't last a week before the holder pulled off when I pulled out the flashlight. What is worse, because the wall is so thin, you can't easily just use wood screws as they don't have enough wood to attach to. So I added a backing plate and put bolts through it to the inside of the closet. There is an air gap between the outside wall and the inside wall so it took 1.5" 6-32 machine screws to reach all the way through and be secured. These are a bit stronger than M3 screws, (sort of an M3.5). It would have been possible to to just use a piece of steel or very small piece of plywood as the backer plate, but this is inside the closet and I did not want the bolts “exposed” and potentially catching on things hanging in the closet. There is a picture included which shows the bolts and how they are set up prior to installation.
Printing
The model prints “upside down.” This is because it is easy to print the gripper perpindicular to the build plate and the backing plate is printed at a slight angle (12.5 degrees as I recall). I wanted the back plate to be printed horizontally for maximum strength. It does not require any supports.
I found no difficulty in printing both parts at the same time in a single print and it took about 90 minutes with 15% infill (default settings for Prusament PLA).
Dimensional accuracy is important as this part has to hold a flashlight with a body machined out of aluminum. If you decide to print it in a filament that has more shrinkage (like ABS) you may need to account for that by scaling a bit in X and Y when slicing.