FlashForge Filament Dry Box
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Still a work in progress. The Dry boxes fit the Creator Pro frame perfectly. I have this dry box sitting on top of an…
- Rating
- 0 / 5
- Likes
- 29
- Downloads
- 61
- Makes
- 0
- Views
- 3,501
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Accessories
- License
- Creative Commons — Attribution — Noncommercial
Still a work in progress. Parts list below.
The Dry boxes fit the Creator Pro frame perfectly. I have this dry box sitting on top of an overturned box.
***12/19/2022 Update***
I ditched the tubing bulkhead adapters. The PTFE tubes slides into the FlashForge extruder tubes.
***1/13/2021 Update***
I'm not a fan of the single bar design any more. Changing out one roll can be cumbersome so I'm probably going to switch to a roller bearing, pedestal for the rolls to sit on instead.
**File List:**
Hygrometer Prob Wire Clip.stl
Holds the hygrometer probe wire out of the way of moving parts, clips to the rear carriage of the extruder pulleys.
Hygrometer Probe Clip.stl
Used to hold the probe of the hygrometer inside the printer.
Tubing bulkhead adapter 6MM smooth to 5MM thread.stl
Adapter for the extruder tubes to connect to the exterior push to connect fittings. I recommend sliding the PTFE into these, then screw the PTC fittings onto them.
Rod Holder 1.stl Rod Holder 2.stl
Holds the 3/4" rod. Need two. One allows you to lift up on one end of the rod in order to slide the spools off.
Tube Covers - Body.stl Tube Covers - Clip.stl
PTFE covers and clip for the unused filament storage. The body is closed and allows for about 1" of exposed filament so you can easily pull the filament through the tubing to feet your extruder.
**Parts:** Sterilite 32qt gasket box:
Fan w/ controller:
PTFE Tube fittings 4mm PTC x 5mm Thread: https://www.amazon.com/STERILITE-32Qt-Clear-Gasket-19334304/dp/B00KL7VQ7S/ref=as_li_ss_tl?dchild=1&keywords=sterilite+32qt+gasket+box&qid=1609335560&sr=8-2&linkCode=sl1&tag=noboysallowed-20&linkId=10a39a4c4bc0d4778d597249c6e8d511&language=en_US
3M VHB 1/2" double sided tape: https://www.amazon.com/STERILITE-32Qt-Clear-Gasket-19334304/dp/B00KL7VQ7S/ref=as_li_ss_tl?dchild=1&keywords=sterilite+32qt+gasket+box&qid=1609335560&sr=8-2&linkCode=sl1&tag=noboysallowed-20&linkId=10a39a4c4bc0d4778d597249c6e8d511&language=en_US
I use 3M VHB exclusively when I need something to permanently stick. It's good to have around. It is expensive, but well worth it over other double sided tapes.
These are optional. I had some on hand. They eliminate the need for a washer or nylon lock nut as the serrated lock nuts hold onto the surface and both bolt and lock nut have washers built in.
3/4" rod. I used a railing baluster as I had some left over from a project. They are 26" long so you can get 2 out of one baluster. I'm not sure if you can buy just one so a piece of black pipe may work from the local hardware store. I prefer metal over wood for sagging.
Print Settings
Printer Brand:
FlashForge
Printer:
Creator Pro
Rafts:
Doesn't Matter
Supports:
Doesn't Matter
Resolution:
0.15
Infill:
25%
Filament: FlashForge PLA
Black
Category: 3D Printer Accessories