Littlejack

Well I finally finished my Littlejack airship model
from Skies of Arcadia.

A very simple guide to help assemble the model.
https://www.dropbox.com/s/x61a6lo4opgkake/LJ_assembly_guide.pdf?dl=0

I have tried to make it as easy as I could to print and reduce as much support material needed as possible.

Check print settings for method I used to print each part.

Print instructions

Below is the print settings I used for each part.
All settings are recommended settings only.

Part file name: LJ_anchor.stl
Layer height: 0.15mm ( this can be done in 0.20mm as well)
Supports: No
Raft: No

How many
to print: 1

========================================

Part file name: LJ_cannon.stl
Layer height: 0.15mm ( this can be done in 0.20mm as well)
Supports: No
Raft: No

How many
to print: 6

========================================

Part file name: LJ_fin.stl
Layer height: 0.15mm ( this can be done in 0.20mm as well)
Supports: Yes (build plate only)
Raft: Yes ( 2 layers)

How many
to print: 4 (I recommend printing one at a time.)

========================================

Part file name: LJ_flag.stl
Layer height: 0.15mm ( this can be done in 0.20mm as well)
Supports: Yes
Raft: Yes (2 layers)

How many
to print: 1

========================================

Part file name: LJ_flap_01.stl
Layer height: 0.15mm ( this can be done in 0.20mm as well)
Supports: Yes
Raft: No

How many
to print: 1 ( has both needed items in the one model file)

========================================

Part file name: LJ_flap_02.stl
Layer height: 0.15mm ( this can be done in 0.20mm as well)
Supports: No
Raft: No

How many
to print: 1 ( has both needed items in the one model file)

========================================

Part file name: LJ_harpoon_cannon.stl
Layer height: 0.15mm
Supports: Yes
Raft: No

How many
to print: 1

========================================

Part file name: LJ_main_hull_01.stl
Layer height: 0.15mm ( this can be done in 0.20mm as well)
Supports: Yes
Raft: No

How many
to print: 1

========================================

Part file name: LJ_main_hull_02.stl
Layer height: 0.15mm ( this can be done in 0.20mm as well)
Supports: Yes
Raft: No

How many
to print: 1

========================================

Part file name: LJ_pins.stl
Layer height: 0.15mm ( this can be done in 0.20mm as well)
Supports: No
Raft: Recommended but up to printer

How many
to print: 1 ( has both needed items in the one model file)

========================================

Part file name: LJ_sail_01.stl
Layer height: 0.15mm
Supports: Yes
Raft: Yes

How many
to print: 1

========================================

Part file name: LJ_sail_02.stl
Layer height: 0.15mm
Supports: Yes
Raft: Yes

How many
to print: 1

========================================

Part file name: LJ_sail_03.stl
Layer height: 0.15mm
Supports: Yes
Raft: Yes

How many
to print: 1

========================================

Part file name: LJ_stand.stl
Layer height: 0.2mm ( this can be done in 0.15mm as well)
Supports: No
Raft: No

How many
to print: 1

========================================

Part file name: LJ_vent_pipe.stl
Layer height: 0.15mm ( this can be done in 0.20mm as well)
Supports: No
Raft: No

How many
to print: 1

========================================