1 / 6
Lathe Crank Handle for 7X Lathe/MiniLathe — image 1
1 / 6

Lathe Crank Handle for 7X Lathe/MiniLathe

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A manual crank for a small lathe

Rating
0 / 5
Likes
12
Downloads
118
Makes
0
Views
1,142
Reviews
0

Updated at source:

Model information

Category
Tools
License
Creative Commons — Public Domain

SAFETY WARNING : Before using this manual crank on your lathe, first unplug the lathe to prevent accidental starting with the crank handle inserted.

This print is actually the parts required for a handle and “spindle nut” and requires additional metal parts to complete the crank, as noted below.

Additional parts required :

  • Handle bolt : ¼"-20 X 4-¼ " hex bolt 
    • correction on Jan. 27, 2024 - length was originally misstated as 5" 
  • Spindle nut : ¼"-20 X 5" carriage bolt (or longer as needed - see discussion)
  • Spindle nut : nut and washer to fit carriage bolt
  • Crank : 6" (150mm) length of ¼" X ¾" (5mm x 20mm) flat bar - adjust length to fit your lathe

A note to my metric friends : I have given some approximate metric equivalents in this write up, but I have not tested them. Equivalent metric parts should work, but I cannot guarantee this.

Additional print files included :

Test ring : My 7X lathe has a spindle with a 20mm ID. I have included a small “test ring” which can be printed to test the fit in your spindle - the test ring should be a sliding fit in your spindle. You can use the test ring to adjust scaling if necessary.

Spindle nut spacer : The spindle nut needs to be long enough to allow for clearance of the handle crank from other parts of the lathe. The version I printed was sized to fit my lathe. If you need additional clearance, I have included a second version (which I have not tested) which includes a “spacer” piece which can be added for additional clearance; the spacer is intended to be scaled in thickness to meet your specific requirements. Of course if you use a spacer, you will need to use a longer carriage bolt.

How it works, and Assembly

The crank works by loosening the tightening nut for the spindle nut pieces so that they can slide into the lathe spindle. Tightening the nut of the spindle nut carriage bolt causes the two parts of the spindle nut to slide apart and wedge into the lathe spindle. Note that the length of the carriage bolt should be a very loose fit in the spindle nut ID, so as to allow for the two spindle nut pieces to slide sideways.

The handle is made from simple steel flat bar as shown in the photos. The hole on the spindle nut end is a clearance hole for the carriage bolt. The hole on the handle end is a tapped hole for the handle. The handle simply screws down tightly, and the plastic handle piece itself does not rotate (this allows for better control as you crank the handle).

The steel flat bar crank piece I used was made six inches (150mm) long - the maximum length I could use on my lathe and still allow for adequate clearance from the base and backstop as the handle rotated. It is likely your lathe will require a different length for clearance, so you will need to adjust this piece for you particular lathe.

See the photos of the assembled and disassembled crank to see how the parts come together.

Print Instructions

I printed in PETG as follows :

  • inner/outer pieces :
    • 4 perimeters
    • 40% grid infill
  • handle :
    • 4 perimeters
    • 25% grid infill

 

CAD

The OnShape 3D CAD files for this are here :

https://cad.onshape.com/documents/b21ab95b275087c2431874de/w/11b145e6f140bce3b31b065f/e/0dd271db1478adf90c31f5e0?renderMode=0&uiState=63cd4d01da6feb72e30a9e24

 

Tags