1 / 8
Sistema filtrante per tutte le stampanti con enclosure/ Hepa filter for all enclosed 3d printers — image 1
1 / 8

Sistema filtrante per tutte le stampanti con enclosure/ Hepa filter for all enclosed 3d printers

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Sistema filtrante hepa per stampanti 3d Hepa filter system for 3d printers

Rating
0 / 5
Likes
5
Downloads
33
Makes
0
Views
761
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

Guida per l'assemblaggio (scroll down for english version)

Lo scopo di questo filtro è di abbattere fino al 99% le emissioni nocive prodotte dalle stampanti 3d, grazie a 2 filtri hepa in aggiunta a un filtro a carboni attivi. Costo totale di questa realizzazione: dai 30 ai 50 euro a seconda di dove comprate il materiale. Il filtro lavora in pressione negativa, quindi funziona anche per enclosure non a perfetta tenuta stagna.

Cominciamo stampando tutti i pezzi che trovate allegati, consiglio petg o asa, infill 20%, nessun supporto richiesto. 

Una volta stampati tutti i pezzi bisogna procurarsi i materiali necessari:

  1. 2 ventole 60x60x25 possibilmente a 24 vdc (vanno bene anche a 12v ma devono avere una buona potenza e portata d'aria), NON usate ventole troppo poco potenti! (almeno 4w a ventola). Se possibile usate 2 ventole uguali tra loro (non fate come me che ho montato 2 modelli diversi) 
  2. 2 filtri hepa dimensioni 60x50x20 mm (sono i filtri dei robot aspirapolvere) 
  3. 1 filtro a carboni attivi delle dimensioni 130x130 (costa 1,30 euro), lo taglieremo poi a dimensione richiesta in seguito
  4. 8 viti m4x10 testa svasata con 8 dadi m4 (per fissare le ventole) 
  5. 3 viti m4x12 testa svasata (per fissare il filtro all'enclosure)
  6. corda in gomma diametro circa 3 mm per fare le guarnizioni (costa pochi euro e la trovate o online o nei negozi di ricambistica/ferramente)
  7. inserti m3 (prendetene una quindicina o piu, servono sempre)
  8. saldatore, stagno, spellafili, cacciaviti vari, trapano
  9. pazienza, quella purtroppo non la vende nessuno :) 

Si comincia :)

Prendete il gruppo principale e iniziate a controllare come è venuta la stampa: non devono esserci blob o imperfezioni in modo che tutto si incastri correttamente.

Una volta verificato ciò prendete le 2 ventole: la freccia che indica il senso di uscita dell'aria deve puntare verso l'esterno: 

Non montate le ventole al contrario altrimenti il sistema NON funzionerà.

Una volta inserite le ventole nella sede, esse vanno fissate: prendete quindi le viti m4x10 e inseritele come in foto: 

Il modello presenta al lato inferiore 3 forature rettangolari: servono per inserire i dadi e stringere le ventole. Aiutandovi con delle pinzette prendete i dadi e con molta pazienza avvitate le ventole anche nella parte inferiore come mostrato in quest'immagine:

Dovreste essere arrivati al punto che le 2 ventole sono montate e avvitate al loro posto, ora è il momento del filtro a carboni attivi: prendiamolo e tagliamolo alla dimensione di 120 x 65 mm e infiliamolo nella sua sede come descritto in quest'immagine:

 

 

 

 

 

 

 

 

 

 

 

Come potete vedere il filtro è perfettamente in sede e pronto a funzionare, ora è il momento di installare la guarnizione laterale: la guarnizione è composta da una corda di gomma inserita nella sede e incollata con un pò di colla per tenerla in posizione. Dovreste trovarvi in questa condizione: la guarnizione è nella sua sede, non si muove e rimane inp osizione (non preoccupatevi se agli angoli rimane un po di spazio, appena la avviteremo all'enclosure si schiaccerà e lo spazio andrà via)

Ora che siamo giunti a questo punto è il momento degli inserti: se vedete il modello nella parte superiore ha 6 fori, in questi fori vanno gli inserti per avvitare il coperchio. Se non avete mai avuto a che fare con gli inserti vi consiglio di fare prima un pò di pratica con delle vecchie stampe. Una volta inseriti tutti gli inserti ci dovremmo trovare a questo punto:

I 6 inserti sono in posizione e pronti. Ora tocca ai filtri hepa. Prendiamo i 2 filtri hepa e il supporto dei filtri: i filtri vanno semplicemente infilati nelle 2 sedi del supporto (non importa il verso in cui li montiate, funzionano in ambo i sensi), NON usate troppa forza per infilarli altrimenti romperete tutto.

 

 

 

 

 

 

 

 

 

 

 

 

Finito di montare tutto è giunto il momento di infilare i filtri nel corpo del sistema filtrante. Prendete il supporto appena costruito e inseritelo nel gruppo filtrante: dovreste arrivare a questo punto:

Come potete vedere calza tutto alla perfezione, rimane solo da montare l'ultimo inserto nel foro del supporto e il coperchio e abbiamo finito :) 

Nel coperchio vanno inserite le ultime 4 guarnizioni (una nella parte frontale e 3 nella parte inferiore), il procedimento è sempre lo stesso.

 

 

 

 

 

 

 

 

 

 

 

Una volta fatto ciò avvitiamo il coperchio in sede e abbiamo finito :), se tutti i processi sono stati fatti alla lettera questo è il risultato finale:

 

 

 

 

 

 

 

 

 

 

 

Ora non vi resta che il filtro nella stampante 3d effettuando un foro nell'enclosure (foro rettangolare di dimensioni 120 x 60 mm). Potete montare questo filtro ovunque vogliate (io ho scelto di montarlo sul retro per fattori estetici). Con questo è tutto, la guida finisce qui, spero vi possa essere utile, buone (e sicure) stampe a tutti :) (se questa guida ti è piaciuta fammelo sapere con un bel like, in caso di qualsiasi dubbio/problema non esitate a commentare)

English version:

The purpose of this filter is to reduce the harmful emissions produced by 3d printers by up to 99%, thanks to 2 hepa filters in addition to an activated carbon filter. Total cost of this realization: from 30 to 50 euros depending on where you buy the material. The filter works in negative pressure, so it also works for enclosures that are not perfectly watertight.

Let's start by printing all the pieces you find attached, I recommend petg or asa, 20% infill, no support required.

Once all the pieces have been printed, you need to get the necessary materials:

  1. 2 fans 60x60x25 possibly at 24 vdc (12v are also fine but they must have good power and air flow), DO NOT use too little powerful fans! (at least 4w per fan). If possible, use 2 identical fans (don't do like me who mounted 2 different models)
  2. 2 hepa filters dimensions 60x50x20 mm (they are the filters of the robot vacuum cleaners)
  3. 1 activated carbon filter measuring 130x130 (costs 1.30 euros), we will then cut it to the required size later
  4. 8 m4x10 countersunk head screws with 8 m4 nuts (to fix the fans)
  5. 3 m4x12 countersunk head screws (to fix the filter to the enclosure)
  6. rubber rope diameter about 3 mm to make the gaskets (it costs a few euros and you can find it online or in spare parts/hardware stores)
  7. m3 inserts (take about fifteen or more, they are always needed)
  8. soldering iron, tin, wire stripper, various screwdrivers, drill
  9. patience, unfortunately no one sells that one :)

It begins :)

Grab the main group and start checking how the print came out - there shouldn't be any blobs or imperfections in order for everything to fit together properly.

Once this is verified, take the 2 fans: the arrow indicating the direction of the air outlet must point outwards:

 

 

 

 

 

 

 

 

 

 

Do not mount the fans upside down or the system will NOT work.

Once the fans have been inserted in their housing, they must be fixed: then take the m4x10 screws and insert them as in the photo:

 

 

 

 

 

 

 

 

 

 

The model has 3 rectangular holes on the underside: they are used to insert the nuts and tighten the fans. With the help of tweezers take the nuts and very patiently screw the fans also in the lower part as shown in this image:

 

 

 

 

 

 

 

 

 

 

You should have reached the point that the 2 fans are mounted and screwed in place, now it's time for the activated carbon filter: let's take it and cut it to the size of 120 x 65 mm and insert it into its seat as described in this image:

 

 

 

 

 

 

 

 

 

 

As you can see the filter is perfectly in place and ready to work, now it's time to install the side gasket: the gasket consists of a rubber cord inserted into the seat and glued with a little glue to keep it in place. You should find yourself in this condition: the gasket is in its seat, it does not move and remains in position (do not worry if there is some space left at the corners, as soon as we screw it to the enclosure it will crush and the space will go away)

 

 

 

 

 

 

 

 

 

 

Now that we've reached this point it's time for the inserts: if you see the model in the upper part it has 6 holes, the inserts for screwing the lid go into these holes. If you have never had to deal with inserts, I suggest you first practice with some old prints. Once all the inserts have been inserted, we should find ourselves at this point:

 

 

 

 

 

 

 

 

 

 

The 6 inserts are in place and ready. Now it's up to the hepa filters. Let's take the 2 hepa filters and the filter support: the filters are simply inserted into the 2 seats of the support (it doesn't matter which way you mount them, they work in both directions), DO NOT use too much force to insert them otherwise you will break everything

 

 

 

 

 

 

 

 

 

 

After assembling everything, the time has come to insert the filters into the body of the filtering system. Take the newly built support and insert it in the filter group: you should get to this point:

 

 

 

 

 

 

 

 

 

 

As you can see everything fits perfectly, all that remains is to mount the last insert in the hole of the support and the lid and we're done :)

The last 4 gaskets (one in the front and 3 in the lower part) must be inserted in the lid, the procedure is always the same

 

 

 

 

 

 

 

 

 

 

Once this is done we screw the lid in place and we're done :), if all the processes have been done to the letter this is the final result:

 

 

 

 

 

 

 

 

 

 

Now you just have to place the filter in the 3d printer by making a hole in the enclosure (rectangular hole of dimensions 120 x 60 mm). You can mount this filter anywhere you like (I chose to mount it on the back for aesthetics). That's all, the guide ends here, I hope it will be useful, good (and safe) prints to all :) (if you liked this guide let me know with a nice like, in case of any doubts / problems do not hesitate to to comment)

 

Tags