USB-C 65W Charger compatible with Ryobi 18v
We calculate the final price from your selected file. You review and accept it before payment.
Preliminary estimate for PETG
€0.54 – €0.67 net (excluding VAT)
For file: Ryobi18v to 65wUSBC cap_0.4n_0.2mm_PETG_MK4_37m.gcode
This is an estimate for one file. You’ll confirm the exact price before ordering.
File and estimate settings
File used for this estimate
Average indicative estimate: €0.61 excluding VAT (range midpoint).
- Weight reported by the author
- 8 g
- Print time reported by the author
- 36.6 min
- Source material
- PET
- Estimate material
- PETG
- Estimate printer
- Bambu Lab P1S - 0.4 nozzle
- Estimate process
- 0.20mm Standard
Indicative estimate for the selected file only, based on the author’s weight and print time. File variants are not added together. The final price is calculated after file analysis.
Saved on this device.
Enough to charge my laptop on the road
- Rating
- 5 / 5
- Likes
- 27
- Downloads
- 111
- Makes
- 1
- Views
- 1,346
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Electronics
- License
- Creative Commons — Attribution — Share Alike
Updated 05/22/2025
NOTE: There is another version of this adapter, before you print this, check out…
https://www.printables.com/model/615935-usb-c-65w-charger-compatible-with-dual-ryobi-18v
This printable adapter allows a single Ryobi 18v battery to power/charge your phone, laptop, or other USB-C / USB device. Using a 4Ah or larger battery is suggested.
Suggested print settings:
- 0.20mm QUALITY
- Prusament PETG (pictured using OVERTURE PETG Grass Green)
- Infill density 20%
- Infill pattern Cubic
- 3 Perimeters
- Supports required
Assemble by printing…
Qty. 1 of Ryobi18v to 65wUSBC
Qty. 1 of Ryobi18v to 65wUSBC cap
…no glue required when also printing with a handle, simply sandwich this in between
Qty. 1 of Ryobi18v to 65wUSBC handle
…requires Qty.4 of M4*12mm (0.7) cap head screw
…or…
Qty. 1 of Ryobi18v to 65wUSBC handle PP storage
…requires Qty.4 of M4*45mm (0.7) hex socket flat head cap screw
Solder wires to the leaf spring battery contacts at about a 45deg. angle, see the 2nd to the last picture for wire lengths, allow all soldered connections to cool BEFORE inserting!!! See the last picture for how the leaf spring battery contacts go in.
Insert the 65W USB-C PD3.0 and 18W QC3.0 Multi Car USB Port 12V Socket Waterproof with Power Switch into the large hole, but do not push in all the way, leave it sticking out about 2cm so it's easier to attach wires to the back.
Use pliers to push the Female Quick disconnects (that you already soldered onto the end of the wires) onto the USB-C socket (pay attention to the polarity!) then push the USB-C socket all the way in.
Screw handle together manually/slowly to avoid melting the plastic.
Here is the USB stick light seen in the pictures.
Safety note: The PowerPole port is designed for 20 to 18V output from the battery pack, this can be used to run other loads.
Caution: The PowerPole port can be used as an input (12 to 24V acceptable) to power just the USB-C charger by itself - BUT ONLY when NO BATTERY is plugged into the adapter. Do NOT attempt to charge a battery in this adapter, charge in approved chargers. The BMS built into all Ryobi 18v batteries will provide a safe low voltage cut-off. Use of this adapter is safe when these instructions are followed, but any use is done at your own risk. Do NOT leave batteries unattended, in direct sunlight, or anywhere near your campfire/cooking stove/open flame, space-heater, or water.
If you need the STLs of these parts, please see:
https://www.printables.com/model/1303958
Don't have a 3D printer yet? That's OK, order already printed from…