Air Cleaner Assembly for Solex 30/32/34 Carbs (Aircooled VWs)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
This is an air cleaner assembly for use in aircooled VWs or other cars that use Solex 32/34/Pic30/Pic30s carburetors.
- Rating
- 0 / 5
- Likes
- 19
- Downloads
- 50
- Makes
- 0
- Views
- 2,166
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Automotive
- License
- Creative Commons — Attribution — Noncommercial
I drive a '71 Brazilian 1500 VW bug. It was stock 1493cc with a single carb, but I did some upgrades to its engine (changed from single to dual carbs, upped the displacement to 1584cc and added Engle W100 cams). One of the premises I wanted for the upgraded engine was that the looks would have to be as stock as possible (alright, the 1500cc Beetle never had dual carbs, but we did had some 1600cc ones in Brazil which had that setup).
So, for air cleaner, I got some VW Brasília dual-carburetor air cleaner assemblies (which use Fram CA3130 paper filters as standard) and replaced the filter with a high flow compatible one that was supposed to be plug-and play.
However, the "stock" (aftermarket) air cleaner pan was quite restrictive due to some structural mounting points that covered about 45% of the intake tube, literally killing the airflow to the carburators and choking the engine in the process. It would pose no trouble on a stock 1300cc engine with Solex 30/32 carbs, but I have cams and I am running a 34 carburator which requires some more air.
I did put some "sporty" conic air filters provisionally but the looks of that didnt please me. So I went to the drawing board and designed an air cleaner assembly that did not have the sections that restrict airflow. But the filters I used provisionally are small, so I am quite confident that the airflow issue was caused not by the filter size, but instead due to the restrictions in the "stock aftermarket" air filter pan (really? 40% of the duct area clogged by structural pieces? no wonder it was choking the car).
This was made considering a standard Solex 30/32/34 carburator as those used in Brazilian aircooled VWs (52mm carburetor-to-filter fittings) and the Inflow HPF4005 air filters (similar to the Fram CA3130 but high flow, 143 mm (OD) x 98 mm (ID) x 57 mm height, but the design is completely parametric, so it can be adjusted in FreeCAD for any carburator/TBI sizes or different models of round air filters. The base does require suppports for printing. The part itself was designed in approximately five hours, including my FreeCAD learning curve during the process LOL.
On VW bugs with dual carbs, you should use the off-centered base, so it can fit inside the engine compartment. As the base just snaps onto the fitment, you can rotate it to find the best position. On VW Bus (Kombi) and other aircooled models you might do just fine with the centered fitment (I didn't test it on other models).
For joining the two sections (lid and base) together, you should use an M6 threaded rod cut to length (according to the filter you use), as well as some flanged nuts for the bottom. I do recommend using wingnuts on the top lid to make it easier to take it apart for cleaning/replacing the filters.
I personally recommend using tougher filaments for this, as the engine bay tends to heat quite a bit on aircooled engines. I used ABS for the initial prototype, later switching to Tritan which was the best I tested. CF Nylon might also be a good choice of material for this project. I wouldn't use PETG because it is a little on the hard side (less flexible) and might crack due to the engine vibration. Rigid filaments with a little flexibility like Tritan or CF Nylon are the best for the job.
If you want to use a breather, you can, there are versions for use with or without a breather (just choose if you want to use the breather on the top of the air cleaner - that's the only option on the centered fitment - or on the bottom, which is an option for the offset fitment).
The files called “New Lid” and “New Base”"are upgraded in the screw holes and might accept heated inserts, but I honestly don't remember if they are sized for Solex 3x or 40's LOL.
This setup ran just perfectly, with no airflow restrictions, and I only took it out because I upgraded my car to Solex40s and went with a chrome EMPI air cleaner kit (so I didn't bother to redo the setup for the 40s which require a larger fitment piece), therefore I stopped updating/improving the design, but it's doable, alright. I also tested the setup with the Fram CA3130 paper air filters and no flow restriction whatsoever.
I uploaded also the FreeCAD files (parametric) are included for anyone willing to remix or improve the project. Just remember to give me the proper credit for the original design, though.
As I am uploading this quite in a rush per a request from the “3D Printing - Auto and Moto” group on Facebook, I'll upload better photos later on.