Filament Sensor Mounting Clip For Cocoon Create Touch and Wanhao i3 duplicator plus Rev1.0
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
This is the OpenSCAD code that was used to make the above clip for holding the filament runout sensor from ebay.
- Rating
- 0 / 5
- Likes
- 2
- Downloads
- 9
- Makes
- 0
- Views
- 123
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- Creative Commons — Attribution — Share Alike
This is the OpenSCAD code that was used to make the above clip for holding the filament runout sensor from ebay.
Rev2: https://www.thingiverse.com/thing:4318121 - This version mount to the extruder motor instead.
Configuration that worked for me in doing filament change in octoprint
https://www.reddit.com/r/wanhaoi3/comments/gi7tqy/configuration\_that\_worked\_for\_me\_in\_doing/
Requirements:
- https://github.com/andrivet/ADVi3pp installed to touchscreen and marlin board
- Octoprint installed and configured to a Cocoon Create Touch or Wanhao i3 Plus printer
- https://github.com/kontakt/Octoprint-Filament-Reloaded plugin installed
- Cheap ebay filament switch
Filament Reloaded Plugin Settings that worked for me:
- Pin : 7
- Debounce Time: 500ms
- Switch Type: Normally Open
- Board Pin Mode: Board Mode
- Gcode: M600 X0 Y0
Pause Print is unticked
ADVi3pp is required for M600 gcode command support for smart filament change.Board mode is based on "raspberry pi pinout" that you can easily google yourself.
High debounce time since physical switches can be a little unreliable.
Untick pause print since the special command already does it for you.
Checking that it works
Go to http://octopi.local/plugin/filamentreload/status and check that you can see {"status":"1"} on each refresh.
Warn:
Colour code of the cheap ebay filament sensor is counter intutative. Don't assume.
Print instructions
Category: 3D Printer Accessories Summary
This is the OpenSCAD code that was used to make the above clip for holding the filament runout sensor from ebay.
Rev2: https://www.thingiverse.com/thing:4318121 - This version mount to the extruder motor instead.
Configuration that worked for me in doing filament change in octoprint
https://www.reddit.com/r/wanhaoi3/comments/gi7tqy/configuration\_that\_worked\_for\_me\_in\_doing/
Requirements:
- https://github.com/andrivet/ADVi3pp installed to touchscreen and marlin board
- Octoprint installed and configured to a Cocoon Create Touch or Wanhao i3 Plus printer
- https://github.com/kontakt/Octoprint-Filament-Reloaded plugin installed
- Cheap ebay filament switch
Filament Reloaded Plugin Settings that worked for me:
- Pin : 7
- Debounce Time: 500ms
- Switch Type: Normally Open
- Board Pin Mode: Board Mode
- Gcode: M600 X0 Y0
Pause Print is unticked
ADVi3pp is required for M600 gcode command support for smart filament change.Board mode is based on "raspberry pi pinout" that you can easily google yourself.
High debounce time since physical switches can be a little unreliable.
Untick pause print since the special command already does it for you.
Checking that it works
Go to http://octopi.local/plugin/filamentreload/status and check that you can see {"status":"1"} on each refresh.
Warn:
Colour code of the cheap ebay filament sensor is counter intutative. Don't assume.