Prusa MK4 Füße mit Dämpfung und M8 Gewindestifte zum nivellieren ./. Feet with cushioning and M8 grub screws for levelling
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Fuss zum einstellen für Prusa MK4 (Enclosure geeignet)
- Rating
- 0 / 5
- Likes
- 2
- Downloads
- 59
- Makes
- 0
- Views
- 577
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Prusa Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Nicht immer hat man die Möglichkeit seine Unterlage,Schrank, Tisch oder Enclosure so auszurichten, das der 3D Drucker Richtig steht.
Mit den selbst gedruckten Füssen könnt ihr euren 3D Drucker (MK4) jetzt ausrichten, was vorher nicht möglich war.
Zusätzlich werden, durch die Gummipuffer, Vibrationen gedämpft und er kann nicht mehr verrutschen.
----------------------------------------------------------------------------------------------------------------
MK4
Teil a und b ergeben einen Fuss.
- Benötigt 2x a und b + 2x Zwischenstück
Teil c und d sind für den Fuss am Netzteil und xBuddy Box.
- Benötigt 2x c und d + 2x Zwischenstück Kurz
---------------------------------------------------------------------------------------------------------
In die Gewindestifte muss noch eine M4 Gewindebohrung gemacht werden damit die Gummipuffer angeschraubt werden können. Ich habe zusätzllich die M4x12 Schrauben eingeklebt mit LOCTITE.
Die M8 Gewindebohrungen habe ich mit einem dreiteiligen Satz (Vorschneider, Mittelschneider und Fertigschneider) Gewindebohrer gemacht.
Es müssen noch Teile zugekauft werden, ich habe mich für A2 Schrauben entschieden, natürlich könnt ihr auch anderes Material nehmen:
6 St. - M8x50 Zylinderschraube (ISK) ----- DIN912 ----- Edelstahl A2
4 St. - M8x40 Gewindestift (ISK) ----- DIN913 ----- Edelstahl A2
4 St. - Gummipuffer/füße
4 St. - M4x12 Zylinderkopfschraube (Schlitz) ----- DIN 84 ----Edelstahl A2
Falls ihr keine Möglichkeit habt in die Gewindestifte eine M4 Gewindebohrung zu machen, könnt ihr auch die Gummipuffer umdrehen und die Gewindest. mit dem Gummipuffer verkleben dann braucht ihr auch keine M4x12 Zylinderkopfschrauben.

Zwischenstück:
Wenn kein Zwischenstück verbaut ist, sieht es nach dem zusammen Bauen so aus:

Mit Zwischenstück:

Englische Version:
It is not always possible to align your base, cabinet, table or enclosure in such a way that the 3D printer is positioned correctly.
With the self-printed feet you can now align your 3D printer (MK4), which was not possible before.
In addition, vibrations are dampened by the rubber buffers and can no longer slip.
----------------------------------------------------------------------------------------------------------------
MK4
Part a and b make a foot.
- Requires 2x a and b + 2x adapter
Part c and d are for the foot on the power supply and xBuddy Box.
- Requires 2x c and d + 2x short adapter
----------------------------------------------------------------------------------------------------------------
An M4 threaded hole must be made in the threaded pins so that the rubber buffers can be screwed on. I also glued in the M4x12 screws with LOCTITE.
I made the M8 threaded holes with a three-piece set (pre-tap, middle tap and finish tap) taps.
Parts still have to be bought, I decided to use A2 screws, of course you can also use other materials:
6 pieces - M8x50 cylinder screw (ISK) ----- DIN912 ----- stainless steel A2
4 pcs. - M8x40 threaded pin (ISK) ----- DIN913 ----- stainless steel A2
4 pcs - rubber buffers/feet
4 pieces - M4x12 cylinder head screw (slotted) ----- DIN 84 ----Stainless steel A2
If you don't have the possibility to make an M4 threaded hole in the threaded pins, you can also turn the rubber buffers around and the threaded rods. glue with the rubber buffer then you don't need any M4x12 cylinder head screws.

intermediate piece:
If no intermediate piece is installed, it looks like this after assembly:

With spacer:
