1 / 1
XL Wash & Cure Station for Elegoo Jupiter (Resin 3D Printing) — image 1

XL Wash & Cure Station for Elegoo Jupiter (Resin 3D Printing)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This is a large format wash and cure station designed to wash/cure parts produced on the Elegoo Jupiter

Rating
0 / 5
Likes
13
Downloads
37
Makes
0
Views
1,394
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

This is designed to be made by re-using the electronics from an Elegoo Mercury XS station, although Elegoo was contacted to buy the parts separately so that the original Mercury XS station could still be used. Elegoo has given the green light to post these files, but included a disclaimer that disassembling the Mercury XS station will void its warranty.

This project requires ~2.5 KG of filament (PETG was used in this case) to print off the included files, as well as some supplies that can be purchased from a hardware store, and some acrylic sheets/glue (Purchased from a local plastics supplier).

B.O.M:

-2.5 KG of filament 

-(20) M3x8 screws 

-(25) zip ties 

-Epoxy

-5 gallon bucket w/lid 

-Metal mesh

-Anti skid surface pads (optional) 

https://www.homedepot.com/p/Everbilt-1-in-Heavy-Duty-Anti-Skid-Surface-Pads-4-Pack-49644/203661092

-Acrylic Glue

 https://www.tapplastics.com/product/repair_products/plastic_adhesives/weld_on_16_cement/132?gclid=CjwKCAjwl6OiBhA2EiwAuUwWZf2Cp5fK9zit3EoRYoVn9EIIhyzRC7gV3fIyhSyxndOxAo6buUprkRoCotkQAvD_BwE

-Amber colored 1/8” thick acrylic sheets 

https://www.tapplastics.com/product/plastics/cut_to_size_plastic/acrylic_sheets_transparent_colors/519

(2)12.75”x12.5”

(2)12.5”x12.5”

(1)12.75”x12.75”

I’d estimate I spent ~$225 on all of the supplies (~$80 of that being for the extra set of electronics from Elegoo so that I could still maintain my Mercury XS station). 

Curing station Instructions:

-3D print the Curing Station (I used my MK3S+, this is designed to be printed in 4 separate pieces and then assembled together using zip ties). I used organic supports in order to minimize material waste 

-3D print the Curing Station Bottom (Once again I used my MK3S+, this is designed to be printed in 4 separate pieces and then assembled using a zip tie in the middle).

-remove the electronics from your Mercury XS station (or use separate electronics purchased from Elegoo). It helps to take a pic for reference for later assembly 

-install the electronics into the new uv curing station, it’s designed to be a very similar assembly 

-install the base of the uv curing station using M3 screws, using the anti-skid surface pads (optional) on each corner 

-print 8 of the “UV curing station acrylic sheet alignment tools”, one is used to hold each corner in place. 

-assemble the acrylic sheets together (minus the top piece which is 12.75”x12.75”) with one alignment tool in each corner, all sheets should have the same height (12.5”) and the front/back acrylic sheets should be 12.75” wide, with the side acrylic sheets sandwiched in between them

-use acrylic adhesive where each acrylic face meets, (careful not to get the acrylic glue on the 3D printed parts), once that dries use more glue along the inside edges, once that dries remove the 3D printed alignment tools and apply glue in areas that were originally blocked by the 3D printed alignment tool 

-place the acrylic lid (12.75”) on a flat surface, apply glue around the top surface perimeter (where the rest of the acrylic sheets will touch) and place the other acrylic sheets on top, once that dries apply more glue along inner edges

Wash station instructions:

-3D print the impeller mount piece (this is the only part that was SLA 3D printed)

-Take a 5 gallon bucket and flip it over,

Flip over the wash station base and place it on top of the bucket. The edges of the wash station will extend beyond the bucket. Line up all 4 corners so that they extend evenly beyond the bucket, and mark where all 4 corners of the wash station base intercept with the bucket (should be 8 markings). Use a utility knife to cut away where the corners intercepted with the bucket (make sure not to cut into the base of the bucket as this could lead to leaks later on). 

-the plastic excess on the bottom surface of the bucket in the middle will also need to be cut away with a utility knife, the bucket needs to sit flush on the wash station base 

-epoxy the impeller 3D print mount into the middle of the bucket (don’t use too much epoxy otherwise the impeller will collide with the epoxy later on)

-once the epoxy has fully dried, take your impeller+screw+washer and screw it into the impeller mount, I ended up using an additional washer on this step to get correct fitment 

-get some metal mesh and cut/form it into a raised circular shape that goes into the bottom of the bucket, ensuring the metal mesh doesn’t interfere with the impeller 

-Enjoy your XL wash and cure station 

 

Feel free to visit our website and to contact us for all of your custom part/prototyping needs! 

https://www.campbellprototyping.com


 

Tags