1 / 8
Soldering Fume extractor /Absauganlage für Lötdämpfe — image 1
1 / 8

Soldering Fume extractor /Absauganlage für Lötdämpfe

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Eine Kabellos Absauganlage mit USB-C Buchse zum aufladen. A Wireless Fume Extractor with a USB-C Port for Recharging.

Rating
0 / 5
Likes
1
Downloads
33
Makes
0
Views
232
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution

An English Instruction is further down. 

 

 

Ein Akkubetriebener Lötdampfabsauger, damit man beim löten nicht die ganze zeit diesen wunderbaren rauch einatmet. Bis zu fünf 18650 Akkus können in das Gehäuse gepackt werden. Mit einem Step-up Wandler werden die etwa 3,7v auf 12v hochgewandelt.

Als Lüfter habe ich einen Arctic 120mm Lüfter benutzt, aber es sollte theoretisch jeder 120mm Lüfter passen (Wenn das gleiche Lochbild 105mmx105mm vorhanden ist ).

Zum drucken habe ich PETG Benutzt, weil es grade im Drucker war😅. Mann kann jedes Filament benutzen was man möchte PETG,PLA,ASA,ABS… allerdings vielleicht kein TPU, könnte sonst etwas wacklig werden.

 

Unteschied zwischen V1 teilen und dem Rest ist, dass das Batteriefach getrennt ist. Die teile sollten mit den neuen kompatibel sein. Bisher wurde nur die V1 gedruckt ich habe für den Upload noch ein paar tolleranzen geändert.

 

Teileliste

( Ich hatte meine über eBay für ein anderes Projekt gekauft und hatte diese übrig)

Sonstige dinge wie Lötkolben ( ohne einen wäre das ganze unnötig), Schrumpfschlauch, Werkzeug wie eine Abisolierzange, Seitenschneider… .

 

 

3D-Gedruckte teile

1x"Filter Gitter" 

1x"Gitter_High_Flow" ODER “Gitter”

1x"Lüfter Halter"

1x“Batterie ach” ODER “Batterie fach_No_Support”( Kein flacher abschluss des gehäuses)

1x“Basis”

 

 

Aufbau

 

Das Kupferband auf die flache Seite des Batterie Faches kleben und abgeschnittene federn in die andere Seite mit den Auskerbungen kleben (Sekundenkleber). 

Alternativ einfach die Zellen direkt zusammenlöten.

 

Den Lüfterhalter auf die Basis Schrauben und den Lüfter anschrauben.

Dann den Gemeinsamen plus und minus pol an die zugehörigen stellen auf dem USB-C Modul löten. Den 5V Ausgang vom USB-C Modul mit dem Step-up Modul verbinden. Das Batteriefach teilweise in die Basis schieben und die Lüfterkabel an das Stepup Modul löten. 

Dann von unten das Batteriefach festschrauben.

Den Aktivkohle Filter ausschneiden (etwa 120x120mm) und in den Lüfterhalter legen und mit dem Filter Gitter Befestigen. Alternativ den Lüfter ohne Gitter laufen lassen und die extra schraubenlänge benutzen um den Filter mit schrauben und Unterlegscheiben direkt zu befestigen.

 

 

 

Description

 

A Battery powered Fume extractor for soldering so your not constantly breathing in the wonderfull soldering fumes. Up to five 18650 cells can be used in order to supply the step up converter with the approximately 3,7v so it can put out the 12v the fan needs.

As a fan I used an Arctic 120mm fan, but theoretically any 120mm fan should do it (if the same hole pattern of 105mm x105mm is available).

I used PETG to print the model. Why you might ask… Because it was already loaded in my printer 😅. You can use any filament you want PETG,PLA,ASA,ABS… Maybe no TPU it might be to wobbly. 

 

The difference between V1 parts and the rest is that the battery compartment is separate. The parts should be compatible with the new ones. So far, only the V1 has been printed. I have changed a few tolerances for the upload.

 

Parts List:

 

 

Also things you need, a Soldering iron( Kind of obvious and the reason for this project),shrink tubing, Tools like a wire stipper, side cutters… .

 

3D Printed parts

1x"Filter Gitter" 

1x"Gitter_High_Flow" OR “Gitter”

1x"Lüfter Halterr"

1x“Batterie fach” OR “Batterie fach_No_Support”(No Flush housing with this one)

1x“Basis”

 

 

Assembly

Glue the copper tape to the flat side of the battery compartment and glue cut springs to the other side with the notches (superglue).

Alternatively, simply solder the cells together directly.

Screw the fan holder onto the base and screw on the fan. Then solder the common plus and minus pole to the corresponding pads on the USB-C module. Solder the 5V output from the USB-C module to the step-up module. Slide the battery compartment partway into the base and solder the fan leads to the stepup module. Then screw the battery compartment from the bottom. Cut out the activated charcoal filter to fit the fan mount ( a 120mm by 120mm square)and place it in the fan holder and fasten it with the filter mesh. 

Alternatively, run the fan without the mesh and use the extra screw length to attach the filter directly with screws and washers.

 

Tags