Ortlieb-style adapter for bike trunk bags
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Ortlieb has a nifty way to attach trunk bags without straps. This lets you leverage that system with strapped bags.
- Rating
- 0 / 5
- Likes
- 9
- Downloads
- 28
- Makes
- 1
- Views
- 860
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Outdoor Sports
- License
- Creative Commons — Attribution — Noncommercial
2024-02-05
I've been developing an improved solution which I will publish soon to address the shortcomings of this one:
- the bag sits down on the mechanism, thus accelerating wear
- the mechanism requires multiple parts
- more assembly time
- more things to break
- the release mechanism requires access to the side of the bag, which could be occluded if panniers are mounted & stuffed with contents
- case in point:
- case in point:
2023-09-15
I'm not sure how much more development I'm gonna put into this. Consider this abandoned unless I publish more updates.
How it works
I studied Ortlieb's video: ORTLIEB | E-Trunk - The Trunk Bag For Your E-Bike
& their instruction manual.

Bag locks simply by dropping the trunk bag onto a rack. The mechanism is very clever & auto-adjusts to any tube diameter, & because it's spring-loaded, there is no gap which would generate rattle.

Removing the bag is a simple operation: disengage one side only & peel off the bag.
Ortlieb's mechanism is integrated into the bag's construction however.
I wanted to be able to bring that to any trunk bag that uses traditional straps. For example, many trunk bags features 4 velcro straps, 1 in each corner.


My design
- I didn't care about adjustability to fit different racks since I mostly use this with a single rack
- I wanted to be able to use this mechanism with a traditional trunk bag that has 4 straps: 1 in each corner
- the construction consists of the following non-exhaustive list:
Rev 6.3
Contact
I played around with many different curves for making the contact: ellipses, eccentric circles, etc., but settled on an Archimedean spiral. It was minorly painful to make this in Solidworks.

The inspiration for this curve was watching this video: Was it Worth Building These? | ft. Matthias Wandel. This timestamp mentions the use of a spiral in an analogous application in woodworking.
Spring action
The mechanism requires the use of springs. Ortlieb's prior art uses torsion springs:

I considered several different torsion spring alternatives, but ultimately used torsion springs as well. For experiment's sake, I also added a hook to install a rubber band or o-ring:


Processing & assembly
- torsion spring assembly could be made better, oh well
- used 3.30 mm reamer for PIVOT BLOCKs
- .137" = 3.48 mm reamer for CONTACTs
- this combo yielded a nice friction fit with the coiled spring pins, assemblable by hand
Performance
- the SPINE was far too flexible to work effectively, but I suspected as much
- the CONTACT worked decently well
- I didn't trim the ends of the springs because I thought I might need them for different future designs – they interfered with the rack rails & disallowed the CONTACTs from fully seating & locking
- otherwise, I was quite pleasantly surprised at how well it worked
Future improvements
- pelvis
- need to stiffen: flip print orientation, add large stiffening rib underneath
- change to m3 CSK instead of m4
- fillets didn't mirror over
- general comments
- mark all parts with REV
- need stronger spring, or preload more
- capture the spring better to ensure it's captive
- spring leg is too long & getting caught on tube of rack
- contact
- deeper rubber band channel
- spine
- add hook & adjustable stop to prevent the bag from going forward & back
- PIVOT BLOCK
- add CSK or CBORE to ends where pin inserts
