1 / 6
MK3S+ and MMU2S MMU3 Big Einsy Out-facing Case with DB9 socket — image 1
1 / 6

MK3S+ and MMU2S MMU3 Big Einsy Out-facing Case with DB9 socket

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Big Einsy case with frame fixing screw slots and lid on the outside, in MK3S+ & MK3S+ / MMU2S - MMU3 versions.

Rating
5 / 5
Likes
10
Downloads
62
Makes
1
Views
547
Reviews
1

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

The Big Einsy case is an awesome concept. This remix addresses the issue of being able to easily access the frame fixing screws, especially after assembly. A channel against the frame has been opened up to route a +5V power cable up to a top-mounted Raspberry Pi4B.

There are two versions. One for the MK3S+ and another for the MK3S+ fitted with MMU2S / MMU3, via a DB9 connector. The DB9 connector is fitted to a holder which is printed separately.

The Prusa style cable clamping system has been preserved for both the extruder and heat-bed looms as much as is possible. The X-Axis motor cable uses the same cable clamp system as the heat-bed so two heat-bed cable clips are required. 

My case prints are in 0.2mm PETG with some paint-on organic supports. If your bridging is excellent, the supports could be deleted.

The MK3S+ case takes 4 thin square nuts for the lid and anther 6 for the cable looms. The MMU case requires an additional 2 for the DB9 holder fixing.

The thin square nuts are set up for nuts 1.79mm thick, sourced from:

https://www.ebay.com.au/itm/292079244600?var=591053828478&hash=item4401479538:g:8TkAAOSw5-plCYqw&amdata=enc%3AAQAIAAABIJNk%2Fa%2FEki%2Fgz9rF4RP4oSjfLfEYtqWFXWtBzdGVc5hdUBtwMI%2BNvA6%2F7fBPV7HKSd3M8fSzekUeXR3BgAmme5RAJx76twof6WuYHmm2q10PVfAkHS25ps5gobHIwodIUo58DGxisEVmA8W2KdvTzzHTL9m3mVD6R9fNTvcyQf1C59ejWQ%2BubnZd0s2toXNgf13RPf1x1kzHRo150o0aB5S6iE%2BuuYXL7l%2F2jBgo3blKpjzFaSdlFcxJ%2FrTVwio0oPbsqHDQXHKAXr4Oofzijwedm05a04a5QgcGaX9fjZgVKpVPZ6OOp93j8tOjOLFLXIEBrtxA1fqk5kHPTT%2B9R%2FM%2BP15X4owUQVaE9EO9DKgd4i4YsaIejIZKxq5xfAIVmQ%3D%3D%7Ctkp%3ABFBMmNT6r_li 

Spare Prusa square nuts, typically 1.72mm will fit just as well. 

The lid takes 4 M3x10 screws.

The Einsy is fixed by 4 M3x10 screws & 4 M3 nuts.

The cable loom clamps require 6 M3x10 screws into thin square nuts.

The MMU case requires an additional 2 M3x10 screws into thin square nuts for the DB9 connector holder.

The DB9 female connector holder accepts 2 x UNC 4-40 jack screws with UNC 4-40 nuts.
The jack screw can be up to 7mm long.

They can be sourced from Amazon:-

 https://www.amazon.com.au/20SETS-Spacing-Screws-Standoff-Connector/dp/B09T5YDM1M?crid=ZTPOB65869M7&dib=eyJ2IjoiMSJ9.B4hbG_F3OVpNCwkstZwEVycJtGtZJSJnok3bEqKuoNKMlnqBVxutkKCZfvpWWPYJ67oZNc35GCfgVBStrkbF94iQnr3qkIF2HGcmvBRt5p4.tG1I7eFNhM9gRf70WBtwWEJ32n2SuL9L6Xl5q5CN5ms&dib_tag=se&keywords=D-

Slots in the back of the case allow a long hex key to reach the socket heads of the frame fixing screws.

Note that the inner frame fixing screws should be inserted into the case prior to mounting the Einsy board. Ignore this step and you will have to remove the Einsy board to get those screws in.

Inserting a hex key into the slots with power on the Einsy board is not recommended.