Christmas star / Weihnachtsstern - English/German
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
3d printed Christmas star controlled by ESP32 and WLED for Christmas tree or window
- Rating
- 0 / 5
- Likes
- 9
- Downloads
- 33
- Makes
- 0
- Views
- 266
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Winter & Christmas & New Year's
- License
- Creative Commons — Attribution — Noncommercial
Deutsche Anleitung am Ende.
Translated with Google Translator
Description
We have had a self-made glowing star on top of our Christmas tree for 30 years. So I thought it was time to do something new. A new star was designed with FreeCad, printed with the 3D printer and animated using ESP32 and the WLED project (https://kno.wled.ge/).
Required parts:
- Bell wire approx. 0.5mm diameter
- LED strip SK6812 RGBW BTF-5V-144L-W (B01MRSVY8G)
- ESP32 D1 mini (B0CM9BR387), ESP32-2 mini lite (B0CJHWD986) or ESP32-C3 supermini
- IR receiver TSOP 4838 optional (B0CZHWVC89)
- Micro INMP441 optional (B0CH2TYXCZ)
See pictures for assembly instructions
- Assemble 6 LED strips with 8 LEDs and tin the required soldering points.
- Pull the bell wire into the guide holes in the middle section and twist the ends and solder them.
- Solder short wire ends to this basic wiring to supply power to the LED strips.
- Trim the LED strips on the inside at the sides and glue them to the middle section.
- Solder short wire ends to previously tinned power supply points on the LED strips.
- Connect the D-Out of the LED strips to the next D-IN.
- Prepare the TSOP4838 and glue it to the middle section and solder it.
- Program the ESP32. (Config and preset are available as a ZIP file)
- Connect the ESP32 to the middle section using 3 or 4 flexible wires. I used Dupont connectors, but it can also be soldered directly.
- Put it into operation. All in all, it takes about 2-3 hours.
The star was tested with the ESP32 d1 mini, the ESP32-S2 mini lite and the ESP32-C3 super mini. ESP32-S2 is cheaper and uses about 50mA less power. The disadvantage is that it cannot currently be programmed directly via WLED Install. However, it is possible if you flash the controller using the ESP-Home Dashboard and then replace the firmware.bin with the renamed WLED_xxxx_ESP32-S2.bin from the WLED project and the partitions.bin with the renamed partitions.zip and program it again. Only necessary for the first programming. The ESP32-S2 can be updated later via OTA.
The front and back should be printed from transparent PTEG or PLA with 3 perimeters and 100% infill. The middle part from PETG with 30% infill. Freecad files are available. I did not use screws. The diameter of the connectors must be such that the parts can be pressed together with a little force.
Have fun printing and crafting.
Deutsch
Beschreibung
Seit 30 Jahren habe wir einen sebstgebauten leuchtenden Stern auf der Spitze unseres Weihnachtsbaums. Da dachte ich das es Zeit ist etwas neues zu machen. Mit FreeCad wurde ein neuer Stern entworfen, mit dem 3d Drucker gedruckt und mittels ESP32 und dem WLED Projekt (https://kno.wled.ge/) animiert.
Benötigte Teile:
- Klingeldraht ca. 0,5mm Durchmesser
- Led Sreifen SK6812 RGBW BTF-5V-144L-W (B01MRSVY8G)
- ESP32 D1 mini (B0CM9BR387)/ ESP32-2 mini lite (B0CJHWD986) ESP32-C3
- IR Empfänger TSOP 4838 optional (B0CZHWVC89)
- Micro INMP441 optional (B0CH2TYXCZ)
Montagehinweise siehe Bilder
- 6 Ledstreifen mit 8 Leds konfektionieren und benötigte Lötstellen verzinnen. (Bild 1)
- Klingeldraht in die Führungslöcher des Mittelteils einziehen und die Enden verdrehen und verlöten. (Bild 2)
- Kurze Drahtenden an diese Basisverdratung anlöten für die Stromversorgung der Led-sreifen. (Bild 4)
- Ledstreifen innen an den Seiten beschneiden und auf das Mittelteil kleben. (Bild 3/4/5)
- Kurze Drahtenden an vorher verzinnten Stromversorgungspunkte der Ledstreifen löten. (Bild 3/4/5)
- D-Out der Ledstreifen mit den nächsten D-IN verbinden. (Bild 6/7)
- TSOP4838 vorbereiten und auf das Mittelteil kleben und verlöten. (Bild 8/9)
- ESP32 programmieren. (Konfig und Preset sind als ZIP Datei vorhanden)
- ESP32 mit dem Mittelteil verbinden über 3 bzw 4 flexible Drähte. Ich habe Dupont Verbinder genommen, es kann aber auch direkt verlötet werden. (Bild 10/11)
- In Betrieb nehmen. Alles zusammen Zeitbedarf ca. 2-3h.
Der Stern wurde mit dem ESP32 d1, dem ESP32-S2 mini lite und dem ESP32-C3 ausprobiert. ESP32-S2 ist Preiswerter und verbraucht ca 50ma weniger Strom. Der Nachteil ist das er sich zur Zeit nicht direkt über WLED Install programmieren läßt. Es geht jedoch wenn man mittels ESP-Home Dashboard den Controller flasht und anschließend die firmware.bin mit der umbenannten WLED_xxxx_ESP32-S2.bin vom WLED Projekt und die partitions.bin mit der umbenannten partitions.zip austauscht und nochmals programmiert. Nur bei der ersten Progammierung notwendig. Später kann der ESP32-S2 über OTA upgedatet werden.
Die Vorder- und Rückseite sollten aus transparenten PTEG oder PLA bei 3 Perimetern und 100% Infill gedruckt werden. Das Mittelteil in PETG mit 30% Infill. Freecad Dateien sind vorhanden. Ich habe auf Schrauben verzichtet. Der Durchmesser der Verbinder muss so sein das die Teile mit etwas Kraft zusammengedrückt werden können.
Viel Spaß beim Drucken und Basteln.