Spool(s) Holder: Printer Mounted
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Modular and configurable spool holder. It can be adapted to other printers, but designed for Prusa Mk3-4
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 17
- Makes
- 0
- Views
- 108
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Prusa Parts & Upgrades
- License
- Creative Commons — Public Domain
I use TPU a lot, and I found issues with any form of resistance, so I wanted to use bearing based mounts, and that helped a lot.
I had tried out several for my Prusa Mk3, and they all worked, but had design issues. With some, the extruder would collide with the filament guide or the spool holder itself if the Z was too big. Some had weak points that would break after time. Some seemed to be made for a different machine and had been adjusted to fit on this one. When I upgraded my Mk3 to a Mk4, I found that the extruder was even taller and the extruder’s clearance with the frame was even less than on the Mk3, both making the collision problem worse. I decided that I needed to start from scratch.
My goals:
• Make it modular, so it can be put together in different configurations depending on your needs.
• Make it modular so you could use it on different machines by designing a frame clamp specific to your machine. All other parts would still work fine.
• Make it modular so that I can add to it as I dream up different stuff I can do with it.
• Make it fix all possible clearance issues, or at least mitigate them.
• Reduce the points of failure due to weak points or wear.
I think I managed all this, but because of the clearance problem, I would be happier if the frame clamp was a little stronger where it contacts the frame, but that might be just me being critical of my own work. Testing has shown it to be plenty strong, but fatigue over time and vibration may make it an issue at some point. There is another point of weakness in the connectors for the filament guide, but this is intentional. If it's configured poorly, I would rather the connectors break than damage the printer.
Note: I upgraded my Mk3 to the Mk4, and I understand that the frame on the Mk4 is slightly thicker, so some sanding may be appropriate for the real Mk4.
The frame clamp attaches to the machine, and everything else attaches to it via four square holes in the clamp. The four holes are .2mm larger than the male counterparts on the platforms and guide supports. Still a tight fit, but it minimizes drooping due to the weight of the spools. Keep this in mind if you want to design your own clamp.
The spool platform comes in two "flavors": Single wide and double wide. If you just need a single spool, all you need is two single wide platforms, and if you are a bit neurotic like yours truly, one of them can be a mirror of the other so they look balanced. If you want two spools, print the double wide and two single wide. If you want three spools, two double wide and two single wide. Four spools is probably possible, but hey, let's not go crazy: It's a single extruder machine.
Single wide platforms have two bearing wheels and double wide have four. You can attach the platforms to the clamp in three different positions depending on how far forward you want the spools, though if you put them all the way forward, you will not be able to use the filament guides. I use them one back from that so I can use the guides. The front wheels on the platforms are fixed, but there are three different places for the rear wheels, adjust according to the size of spool, or how far back you want the spool. On the double wide, the placement of the rear wheels can be different to accommodate your needs. The wheels use 608 bearings that I de-grease and oil, just because. The axles should attach to the platform with an audible snap.
The guides are supported by slotted posts intended to attach to the front square of the clamp. Different guides can be attached to these slotted posts depending on how you want to configure it.
Short story: It is configurable out the wazoo, and you only need to print the parts that you require for your particular needs.
For most non-TPU things, as here, I use PETG. I suggest that you print .10 detail with a .4 nozzle because of the tolerances, and I suggest that you increase the parameters so that there is no infill in a weak point like the clamp where it attaches to the frame. Most parts are far stronger than they need to be, but then I usually over-engineer things: Probably a trust issue. You will need supports for the clamp: I suggest organic for this one (or sanding may be required), and print it inverted. Both platforms, the axles, the wheels and the guide supports will need supports of your choice: I used snug with .2 top and bottom contact distance.
Gord Lawry