#0143 Cable Inlet Cover - Up to 4 Cables, Original Prusa Enclosure (OPE)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Covers up slits that are each equivalent to a 14.6mm diameter hole, at 2 locations.
- Rating
- 5 / 5
- Likes
- 90
- Downloads
- 447
- Makes
- 22
- Views
- 1,488
- Reviews
- 22
Updated at source:
Model information
- Source
- Printables
- Category
- Prusa Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
*** Thanks for checking out this model! ***
If you appreciate what I'm doing, consider buying me a coffee, and check out my other models for something else you might like!

**********
Looking for MORE upgrades for your enclosure? Consider doing this one too!

**********
I like the sturdiness of the Original Prusa Enclosure with all sorts of mounting locations for enhancements! However, that also means it has many areas where heated air could escape, and I've been focused on creating solutions to plug up all of them!
This cover can be installed after you cut out the pass-through opening. Simply use a side snipper to cut the tabs holding it in place. You don't need to cut them that precisely because this cover has clearances for tab remnants. It gives you some good options to allow up to four cables to pass through if you'd like - and still minimize the air leakage from that area.
Along with my other heat retention upgrades (shown further down below), this one offers 5 options:
- Simply plug the slits - does not accommodate cables
- One opening - Allow 1 cable up to 5mm diameter to pass through, or 2x cables up to 3mm diameter.
- Two openings - Allow 2 cables up to 5mm diameter to pass through, , or 4x cables up to 3mm diameter.
- Three openings - Allow 3 cables up to 5mm diameter to pass through, or 6x cables up to 3mm diameter.
- Four openings - Allow 4 cables up to 5mm diameter to pass through, or 8x cables up to 3mm diameter.
NOTE: You can fit more cables per pass-through if they are smaller than 3mm diameter, but you'll need to experiment for yourself on a case by case basis. :-)


NOTE: Shown above is for the left side of the enclosure (as viewed from back side). You can also make a cover for the one on the right side as well.
TIP: if your friend with a helping hand is not available, use 2 pieces of scotch tape to hold the part in place temporarily while you install and tighten the screw, like so:

Printing Notes:
- Since this location will see higher temperatures, for best results use PETG/ABS/ASA.
- NO supports are needed. As oriented on the build plate, the hole above the nut pocket may appear to need supports, but since it's so small, it will “cheat” gravity and print fine. Normally, you can expect that hole to “mess up” a bit for the bridging layer but the print will recover nicely. The exact feature in a larger size would need support, though, FYI.
- If you use supports, they may get stuck in the lower “blind” hole or at least make it a hassle to remove.
For best results with heat retention, I suggest you download and print my other designs as well:
- Extra Rivet Plugs: https://www.printables.com/model/537013-xrivets-for-prusa-enclosure-extra-rivets-plugs
- Corner Caps: https://www.printables.com/model/552596-original-prusa-enclosure-corner-caps-from-the-insi
- Slit Covers: https://www.printables.com/model/537014-prusa-enclosure-slit-cover-plug
- Hex Vent Hole Cover: https://www.printables.com/model/809977-hex-vent-hole-cover-original-prusa-enclosure-ope
- LCD Cable Exit Cover: https://www.printables.com/model/809972-lcd-cable-exit-cover-original-prusa-enclosure-ope
- LCD Cable Exit Cover with Accessory Cable Pass-through: https://www.printables.com/model/786143-lcd-cable-exit-cover-with-accessory-cable-pass-th
- Front Bottom Cover: https://www.printables.com/model/1096783-0190-front-bottom-cover-original-prusa-enclosure
- PSU Cable Pass-thru Cover: https://www.printables.com/model/809966-psu-cable-pass-thru-cover-original-prusa-enclosure
- PSU Pass-through Cover (Blank): https://www.printables.com/model/859757-psu-cable-pass-thru-cover-blank-original-prusa-enc
- “Mystery Hole” Cover: https://www.printables.com/model/859763-mystery-hole-cover-for-original-prusa-enclosure
- Front Bottom Corner Cable Pass-through Cover: https://www.printables.com/model/859761-front-bottom-corner-cable-passthrough-cover
- Rear Bottom Corner Cable Pass-through Cover: https://www.printables.com/model/859759-rear-bottom-corner-cable-passthrough-cover
- Threaded Bottom Panel Hole Cover: https://www.printables.com/model/873425-miscellaneous-bottom-panel-hole-plug-original-prus
- I will be releasing an Automatic Enclosure Heater as well…check back soon!
Other things you'll need:
- 1x M3x6 or M3x8 socket head cap screw per printed cover.
- 1x M3 square nut per printed cover.
Note: if you are using square nuts from Prusa kits, they tend to be on the smaller side and will fit a bit loose in the nut pocket, so use something to wedge it in to keep it in place or use a dab of CA glue.
**********
If you add this to your collection and/or download the model, please click the LIKE button and give it some STARS!
Remember, you can earn some Prusameters if you post a pic of your make! Plus, it would make my day to see it. ;-D
Happy Printing!
P.S. Please post some constructive feedback if you'd like to see something improved.