#0153 Rear Bottom Corner Cable Passthrough Cover

*** Thanks for checking out this model! ***

If you appreciate what I'm doing, consider buying me a coffee, and check out my other models for something else you might like!  

 *********

This opening is another source of hot air leakage - it's as big as a 20.5mm hole! Covering it (and others) up is part of a bigger project of mine to plug up ALL the sources of air leakage so the enclosure can heat up faster and max out at a higher temperature even without active enclosure heating.  

Features:

1. Simple one part cover that snaps in place.

2. Installed from the inside so you don't have to disconnect anything to install it.

3. Prints quickly and without supports.

Comes in 2 Variants:

1. The “1” variant accommodates ONLY the accessory power cable for Prusa's LED Light Strip / Advanced Filtration System.

2. The “2” variant accommodates the BOTH the accessory power cable and a standard 5.5mm diameter(6mm max) jacketed Ethernet cable.

NOTE: Do you want a "blank" one that blocks anything from passing through?  Click here: 

Recommendations:

1. Use PETG/ABS/ASA.  Tested with Polymaker ABS Black.

2. PLA is not suitable for the function of this model - it's not great at resisting higher temperatures and will take a set over time and start loosening up.

3. 0.2mm layer and 0.4mm nozzle works fine.

4. Use textured Prusa print plate to match the texture of the enclosure.

Installation:

1. First, insert and align the catches next to the cable opening.

2. Push down and towards the LEFT side - firmly - to snap it in.  Be careful that no cables are pinched before you snap it in place.

3. That's it, you're done!

For best results with heat retention, I suggest you download and print my other designs as well:

1. Extra Rivet Plugs: https://www.printables.com/model/537013-xrivets-for-prusa-enclosure-extra-rivets-plugs

2. Corner Caps: https://www.printables.com/model/552596-original-prusa-enclosure-corner-caps-from-the-insi

3. Slit Covers: https://www.printables.com/model/537014-prusa-enclosure-slit-cover-plug

4. Hex Vent Hole Cover: https://www.printables.com/model/809977-hex-vent-hole-cover-original-prusa-enclosure-ope

5. LCD Cable Exit Cover: https://www.printables.com/model/809972-lcd-cable-exit-cover-original-prusa-enclosure-ope

6. LCD Cable Exit Cover with Accessory Cable Pass-through: https://www.printables.com/model/786143-lcd-cable-exit-cover-with-accessory-cable-pass-th

7. Front Bottom Cover: https://www.printables.com/model/1096783-0190-front-bottom-cover-original-prusa-enclosure

8. PSU Cable Pass-thru Cover: https://www.printables.com/model/809966-psu-cable-pass-thru-cover-original-prusa-enclosure

9. PSU Pass-through Cover (Blank): https://www.printables.com/model/859757-psu-cable-pass-thru-cover-blank-original-prusa-enc

10. Cable Inlet Cover:  https://www.printables.com/model/809962-cable-inlet-cover-up-to-4-cables-original-prusa-en

11. “Mystery Hole” Cover: https://www.printables.com/model/859763-mystery-hole-cover-for-original-prusa-enclosure

12. Front Bottom Corner Cable Pass-through Cover: https://www.printables.com/model/859761-front-bottom-corner-cable-passthrough-cover

13. Threaded Bottom Panel Hole Cover: https://www.printables.com/model/873425-miscellaneous-bottom-panel-hole-plug-original-prus

14. I will be releasing an Automatic Enclosure Heater as well…check back soon!

**********
If you add this to your collection and/or download the model, please click the LIKE button and give it some STARS!

Remember, you can earn some Prusameters if you post a pic of your make!  Plus, it would make my day to see it. ;-D

Happy Printing!

P.S. Please post some constructive feedback if you'd like to see something improved.