EnXlosure Prusa HEPA Filter Fan Mod
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
This lets you utilize the Prusa advanced filtration system with your Prusa XL and EnXlosure enclosure.
- Rating
- 5 / 5
- Likes
- 22
- Downloads
- 115
- Makes
- 1
- Views
- 955
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Prusa Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial
Back Story
I wanted to utilize a HEPA filter for my newly enclosed Prusa XL5TH (thank you again @Voxel3D) for Carbon Fiber reinforced PolyCarbonate. I looked into using that cool ALVEO3D filter (the AlveoONE), but it didn't look possible to get the components here in the states. Then I looked more closely at my MK4 with Prusa Enclosure and advanced filtration. Sure enough it was made by ALVEO3D, AND on top of that I could keep stock in the same filters and fan, for future maintenance.

Go easy on me please, this is my first shared 3D model. I did my best to design a solution that prints really good without supports (v4) or with a small amount of organic supports (v5). I also provide the .dxf file for laser cutting or CNC milling of the exact cutout and m3 holes. And since this is just the fan portion, you can choose which of your acrylic panels you want to cut this out on and install. I chose the back bottom panel (the larger of the two panels in the back), towards the bottom and middle, with the lower 4 screw holes about 40mm off the bottom edge. But you can choose to put it anywhere you want, just remove your panel, place in your laser or cnc, and determine where you want this to be placed. I will also note, that Prusa chose a similar location to me with their latest release of the Prusa XL enclosure (they also used their same fan/filter, just with different attachment). I've had mine created for weeks now, and had Prusa came out with their XL enclosure sooner, I might have been tempted, I have a LOT of hours into this enclosure and now customizations like this filter mod.
What's Included
I supply 2 versions of the same filter/fan system.
- v4 is in 2 parts, where 99% is printed without supports and the small remaining piece is glued on with CA.
This version has no wasted plastic and prints great. - v5 is an all in one part, and is printed with organic supports. This version is ready to use after you remove the supports
- .DXF file for either laser cutting or CNC'ing the filter opening and 8 m3 holes
Printing Suggestions
- I would print this in at least PETG
- 4 perimeters, first layer height of 0.2mm and layer height of 0.15mm
- 20% infill with the Gyroid fill pattern
- for v5, I would use Organic supports (with "For support enforcers only" enabled) and either use my .3mf file, or paint on supports under the square 100mm overhang and the round 80mm circle overhang (the circle doesn't have to have the supports, but will be much better shaped if you use organic supports.
- I wouldn't lower the Gyroid infill percentage or perimeter number, as there are 10 heat inserts on this part that will be holding up a running fan from a piece of acrylic.
What's Needed
- QTY 1: Prusa Advanced HEPA Filtration System (by ALVEO3D)
- QTY 1: Basic control board and PSU for the filtration system (and LED)
- QTY 2: rutheX m4 brass heat inserts (m2+m3+m4+m5 assortment of 270)
- **QTY 8: SS m3x8mm pan head machine screws (pack of 100)
- **QTY 8: rutheX m3 VORON (RX-M3x5x4) brass heat inserts (pack of 100)
** You most likely have this many left over from your EnXlosure build
TIPS & TRICKS
- the fan body from alveo3d seems to have been injection molded and as such, be aware that you may need to trim some of the far edges to fit perfect. I didn't want this system to be too loose as it requires no air gaps in certain places, for efficient filtering.
- due to heat inserts, I highly recommend using 4 perimeters and 20% Gyroid infill, this applies to both v4 and v5
- on v4, the prusa slicer will give you a warning about using supports. Just turn on "support on build plate only" and it will be fine (plus not use any supports). At the top underside of the fan circle (80mm), you might get a tiny bit of non-perfectness, but its no big deal, just knock it lose or trim.
- the opening (the top layer of the print) is where you will slide the filter out and replacement back in. The tip here is to install this upright as it is printed. I don't think the filter would ever wiggle it's way out if you installed downwards, but you never know.
- use some 100% silicone when assembling and against the acrylic. It's not necessary, but will ensure no suction leaks for max efficiency.
CREDIT
Voxel3D_Nederland Original EnXlosure for the Prusa XL