1 / 7
Reparatur-Dichtschelle DN25 - 33,7 mm 1" — image 1
1 / 7

Reparatur-Dichtschelle DN25 - 33,7 mm 1"

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Reparatur-Dichtschelle DN25 - 33,7 mm 1" für Notreparatur bei Rohrbruch.

Rating
0 / 5
Likes
0
Downloads
26
Makes
0
Views
99
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — NoDerivatives

Reparatur-Dichtschelle DN25 - 33,7 mm 1" für Notreparatur bei Rohrbruch.

ACHTUNG !

Die Verwendung dieser Teile kann die Gefahr mit sich bringen das es zu einem erneuten Wasserschaden kommt, mit dem Download bestätigt der Empfänger / Verwender dies auf eigenes Risiko zu tun!

Ich schließe hiermit jegliche Haftung aus!

Da ich ein Älteres Haus besitze und es in solchen zu defekten Rohrleitungen kommen kann und ich neulich einem Installateur bei so einer “Notreparatur” zugesehen habe kam ich auf diese Idee.

Das Wasser konnte zu dieser Zeit nicht abgestellt werden und er hat eine ähnliche Reparatur-Dichtschelle (Seine war ein Kaufteil aus Metall) in ca. 5 Minuten angebracht und sie hält dicht. 

Es sind nur 2 der hier bereitgestellten Teile erforderlich.

In jedem Fall Schelle Kopf DN25-33,7mm

und hierzu wahlweise entweder Schelle M8 DN25-33,7mm

oder Schelle Mutter DN25-33,7mm

bei der zweiten Variante werden dann noch 6 Stück M8 Muttern zu den in jedem Fall benötigten 6 Stück M8 x 30 Schrauben DIN 912 benötigt.

Als Dichtung ist ein Stück Gummi aus einem Fahrradschlauch geschnitten 

vorgesehen 70 x 95 mm.

Anwendung:

Die beiden gewählten Teile neben der undichten Stelle des Rohres mit der Gummidichtung “lose” vormontieren und erst vor der endgültigen Montage gezielt über die undichte Stelle schieben. Dann gleichmäßig anziehen, bis es dicht ist. Vorsicht es ist nur Kunststoff.

(ich denke je nach Druckergebnis und Füllgrad maximal 12-14 Nm)

Als Material empfehle ich PC oder PETG in dieser Reihenfolge.

Auch wenn das Ergebnis der Bohrungen und Gewinde für die Schrauben etwas darunter leidet in jedem Fall stehend drucken!!!

Der Füllgrad sollte möglichst hoch gewählt werden am besten 100% aber mindestens 80%.

------------------------------------------------------------------------------

Google translates:

Repair sealing clamp DN25 - 33.7 mm 1" for emergency repairs in the event of a pipe burst.

DANGER !

The use of these parts can involve the risk of further water damage. By downloading, the recipient/user confirms that they are doing this at their own risk!

I hereby exclude any liability!
Since I own an older house and can have defective pipes and I recently watched a plumber doing such an “emergency repair”, I came up with this idea.

The water could not be turned off at that time and he has a similar repair sealing clamp (his was a purchased metal part) in approx.
Installed for 5 minutes and it stays tight. 

Only 2 of the parts provided here are required.

In any case clamp head DN25-33.7mm

and either clamp M8 DN25-33.7mm

or clamp nut DN25-33.7mm
In the second variant, 6 M8 nuts are required in addition to the 6 M8 x 30 DIN 912 screws required in each case.

A piece of rubber is cut from a bicycle tube as a seal 

intended 70 x 95 mm.

Application:
Pre-assemble the two selected parts next to the leaking area of the pipe with the rubber seal “loosely” and only push them over the leaking area before final assembly. Then tighten evenly until tight. Be careful, it's just plastic.

(I think a maximum of 12-14 Nm depending on the printing result and filling level)
As a material, I recommend PC or PETG in that order.

Even if the result of the holes and threads for the screws suffers a little, in any case print standing up!!!

The filling level should be as high as possible, preferably 100% but at least 80%.