All models

NSFW Nude Posing Women - A Complete Chess Set

Contour Gauge -Print-In-Place

Most contour gauges require a lot of separate prints to be assembled after printing, this alleviates that annoyance. This is designed to provide a way to measure, not sketch. Lid screws in to adjust fin tension or to lock fins in place.…

Hyphoon - LARGE Herb Grinder

No really its bigger than you are expecting. Print, assemble, grind, enjoy. Mods: Drum Handle - reduced print time, reduced storage, easier handle spinning (lower torque, not an issue to begin with however) Funnel Drawer - Adds sweeping…

Cat Sized Antlers

Print in current orientation with supports. PLA might be too brittle. May need glue, depending.

Mushroom Earrings

Designed for 3d printing in multiple parts. 0.1~0.15mm clearance on mating parts, designed to be glued together.

Spoon rest

Rest for spoons and lids etc.

Paper Towel Holder - Suspended

Print, assemble, screw into overhead space. Slide roll in and down once the holders are in the roll. Pull up then out to remove empty core. Print instructions Print

Mini Pocket Knife v3 for #11 Exacto Blades

The original design by @Magmabow is a fantastic design but i had trouble printing it with my 0.6mm nozzle. as such, this project was born. Includes a slide safety. Uses M3x8 screws and nuts (x2). no glue required.

Princess Rosalina Star Crown

Add supports to very bottom of stars for ideal print quality. Consider additional perimeters for overhangs in slicer settings.

Adventure Time Marceline's Bass Axe

Model contains printable parts, which need re-orienting. Designed for 2" XPS foam body and neck Included PDF is 1:1 ratio printable at 30x42" (Arch E1 Size). that means printed as-is, it is life sized.

The Herb Typhoon - Weed grinder v1.1 UPDATED

There is no plastic-on-plastic contact in the mauling chamber, as a gap provided for the herb to pass through eliminates the possibility of printed parts wearing plastic into your collected herb. Uses (5x each) M3x20 SHCS and nuts…

Stonk Grinder

A Highly Printable Grinder For Your Greens Print instructions Print in Natural PLA for maximum health safety. DO NOT SMOKE PLASTICS THATS DUMB AS HELL!! requires: 1x M2 x 20mm SHCS 1x M3 Nut 1x 608 "skate" bearing The "retainer pin" and…

3/4-16 UNF Male Thread Adapted To Reverse Thread 14x1mm Female

STL model units are mm

Mobula 7 Replacement Frame

printable without supports. may need to re-drill the circuit board mounting screw holes, as they are only 1mm diameter. The STP file contains separate sub objects which are not joined to each other. you will need to perform a Boolean…

PlayingStation 5 - Raspberry Pi Case

This is a Case for Raspberry Pi boards. Designed to work with a 28mm marine USB and/or HDMI extender, and a 12mm momentary 12vdc switch with LED, neither are required for use. Uses 10mm magnets, and standard M3 hardware. Glue nuts in the…

Alcohol Pad Dispenser 50 and 100 ct.

for 50 (~55)mm disposable alcohol pads. Print instructions There are small tabs at the edges of the overhang where the pads are pulled out. you will need to clean this area up with a knife. pads are designed to come out and down at a 15…

Buddah Biggie

Covered under CC Share Alike only because OG model is. I prefer Public Domain Dedication. The Buddah Model was added to thingiverse by user https://www.thingiverse.com/geoffro/designs

Golden State Warriors Arena

Chase Stadium in San Francisco Print instructions Columns were added to enable overhangs.

Golden 1 Center With Arena Cavity

Removable Lid means you can fill it with weed... or whatever.

Voxelab Proxima Resin Vat Body

Body - Print with MINIMUM 4 perimeters, Lots of infill. Model is optimized for 0.15mm layers Clamps - Print SOLID The body with the "print aids" does not need support material Materials and methods 20x M3x5 countersunk + 20 M3 nuts 10x…

Solar Hat Fan

Designed to fit the motor, fan, and solar cells from the Amazon item KingBra Summer Sport Outdoor Hat Cap with Solar Sun Power Cool Fan for Cycling . After 3d scanning a hat with Photogrammety (used my cell phone + AGI Metashapes) I…

Liquid Mixer

Works well at mixing without introducing air bubbles. you may need to glue the impellers in place if tolerances aren't working for you.

Magsafe Duo Holder

3D Printable without supports. includes integral 1st and 2nd layer stress reduction grooves to reduce both elephant footing, and to assist high temp materials to grip the build plate without excessing thermal stress on the entire base of…

Inner Children

for https://www.reddit.com/r/3Drequests/comments/11dhf1y/mental_health_care/ A reasonably self explanatory sculpture made for printing, based on a sculpture from Burning Man by artist Alexander Milov…

160 Folsom Tower

A kind of neat tower design in San Francisco

Wichita Keeper of the Plains - Repaired

'Keeper of the Plains’ statue located on the river near downtown Wichita, KS – as per original model description. Original model created by user “headwindh” on sketchfab, where they set the license as CC - Attribution

Rounded 2020 Mazda Keyfob Housing

No idea if it works, I can't validate the original design which I've remixed, as this isn't for me personally. Hopefully someone posts a make to validate it with the fob internals installed. Original author used CC4.0 Attribution…

Spiky Goth Dildo Casting Project

Craftsman Drawer Dividers

UPDATE: These somehow did not fit a different Craftsman drawer set I tried, so I've made the "Craftsman Refit Dividers" for newer Craftsman drawers. The older style only had 1 divider per drawer, and dovetail angled divider guides. The…

Bowtie and Pocket Square

Printable Bowtie Clips to Elastic Band. Printable Pocket Square

Bowden Feeder Tube Holder

Designed to clip onto 20mm extrusion, with optional 3mm hole for fastening to T-Nut. For Reverse Bowden PTFE Feeder. There is an optional section for PTFE between the two fastener prongs. Renders shown with PTFE in the middle. Print…

3D Systems Sense (v1 v2) 3D Scanner Replacement Chassis

Pistol-style handle to use the 3D Systems Sense 3d Scanner family with Skanect Software, which assumes a different orientation. I use the OpenNI2 Drivers to use this scanner with Skanect. (The 3D System Sense Scanner is just the Intel…

RocketLeague-esque Multipart Goal

Glue or leave unglued for disassembly. the cutout frames have small holes in the corners to allow use of 1.75mm filament to wedge meshing/fabric into the cutout frames. Modular design can be any width you want.

Bottle Stein

pins go in holes, halves go together. I'd glue and paint. Can be a tight fit if the pins aren't deburred well, or printer tolerances aren't up to spec.

Mini Safe For Personal Storage

A small keychain safe that snaps closed. Two versions are available, a plain version and a decorated version with my log

2008 Mazda CX-9 KeyFob Conversion Kit

The keyfob should pry apart at the chevron between the key and remote buttons sections of the keyfob. After separating the unit, you may carefully insert the fob remote cap with snug pressure. remove the + screw on the backside of the key…

Power Rangers Collectable Coins Set

A set of 7 Coins nesting within a larger 8th, featuring Power Ranger characters on the “heads” side of the coins, and one of the character's ‘Zord’ on the back side for the “tails” side of the coin. All 3d model files are in STEP format,…

Clamping Headphone Rest

Use either the included print in place 608 (skate) bearing, or source your own 608 bearing. epoxy the bearing into the clamp arm, and then the swivel arm bearing post into the bearing, then the swivel arm bearing post cap on said post.

Rocker Ryderz - Bottle Rocket Slip-On Ordinance

Rocker Ryderz are ultra lightweight vase-mode printable assemblies of real world ordinance, optimized to slide on to a standard MC401 Black Cat Bottle Rocket (1.4G), which has a charge diameter of 6.3mm (stick not included). if your…

20cm of Twisted rope (~1.3mm dia)

rope has a flat bottom. I encourage use of a brim.

HMTECH 10.1" LCD Screen Stand-In

A reasonably accurate depiction of the physical form/constraints of the HMTECH 10.1" captivate touch LCD screen. Use this to create your own cases or covers etc.

Ink Slinger - Printing Press

Printing press made from printed parts, B52 Unistrut with 3/8" fasteners, 3/8" threaded rod and nuts, as well as M8, M5, and countersunk M4 screws, 4" polished steel conduit, standard 608 “skate” bearings, and a linear slide rod i had…

Large Photo Backdrop

big ass backdrop, scale to fit your needs

JB Weld 5 Min Epoxy - 4 Oz Cap replacement

A quick and easy print to replace the standard JB Weld cap. Offers easier grip, and as good retention as the original had.

The Poo Peer

3D printable design for **temporary** use. Please don't use this a bunch and keep it kicking around, that's gross. get a real one. But it will get you out of using a fork if you need one bad.

Staff Whacker 5001 - Nerf Blaster

Using a clear tube from a FLUM vape device, and 2x 12x40mm compression springs, 4x M3x10 Screws w/Nuts, 1.75mm Filament as a dart rest/block, and 10-32 allthread. This device relies on the flexible/compliant nature of plastic, in order to…

Voxelab Proxima 6 FEP pattern

Voxelab Proxima 6 FEP pattern

Bayonetta Scarborough Fair - Handle2.stl - Fixed Mark

The OG model has a logo mirrored on one side, making it unreadable, this fixes that

Bong Sucker / Blower For Desktop Vacuum

Designed to fit the small desktop vacuums that are all over amazon etc. Put on top of a bong and turn it on, you can either put your face up to the blower and take the hit that way, or put the blower in the hitter taper to blow it out, or…

Paresu / Valese Dragonball Cosplay Choker Charm

No supports required, as there is a disposable support integrated in the file already. I've added a touch of thickness and made the choker slit deeper since the photos of the print were taken.

Kodak Chamera Reference Model

Model that you can use to design accessories etc

Mold for Silicone Mold Of My Chocolate Face "Whack-a-Orange"

Print the mold. Cast Silicone. Cast Chocolate (etc) into cleaned completed silicone mold. After removing wedges, place in assembly seat (pictured in blue) and pipe more melted chocolate into the void in the center. Wedges assemble in…

Bernina Foot Pedal type 01

STP model of a Type 01 Foot pedal switch for Bernina sewing machines. Use as basis of design for accessories.

Miniature Watering Pitcher

This was designed with my resin printer in mind, and the model orientation is *not* optimized for either SLA or FDM. If you print this FDM, make sure the inner funnel bottom is parallel to your build plate; as-is there would be a need for…

Bezel 220mm x 181mm

220 x 116 x 9.917 mm [Outer Dims] 194.60 x 163.40 mm [Plexiglass Insert Dimension] 182.6 x 152.6 mm [Innermost Dim] 212.80 x 173.80 mm [Cutout Required Dimension] 1.50 mm [Bezel Thickness] 8.42 mm [Thickness Minus Bezel] No dimensions…

Olympus Trip 35 Lens Cap

Designed to print in TPU however hard plastics may work. I've not tested. I used octogram spiral infill for the bottom layer.

Shower Goodies Holder

For a redditor

Mushroom Hut Earrrings

Cute lil' house to print and paint, or print in multi color.

STA CDA

STA CDA

Logitech C920 / C930e Webcam Shell - Leica Inspired

A multi part printable shell casing for a Logitech C920 / C930 Webcam, removed from the manufacturer's shell. NOTE: I've updated the files: Removed the mount i previously designed to be printed, and updated the design to implement the…

Smooth Mario Star Butt Plug Topper