Counting matching models…
Download the Installation guide and read carefully before taking on this modification. Go to the files tab page and scroll down until you find the PDF file for the installation guide. This extruder requires you to remove material from…
Update: 09.06.24. Installation guide added. Update: Also see my new Libra & Trigger Extruders that uses Orbiter internals. By popular request, new threaded insert mounting version. Also see original version here:…
Download the Installation guide and read carefully before taking on this modification. Go to the files tab page and scroll down until you find the PDF file for the installation guide. This extruder requires you to remove material from…
Parts to replace the z-axis wheel carriage with linear rails. See PDF doc for brief fitting guide.
Update: Also see my new Libra & Trigger Extruders that use Orbiter internals. There is now a threaded insert mount version in addition to this one, see link:…
Original Bambulab hotend & CR touch z probe version. There is also BIQU Microprobe & E3D Revo CR remix versions now. Ender 7 replacement toolhead with direct drive extruder, integrated bed mesh probe, improved cooling and cosmetic…
Update 01.04.24. Stepper Motor Brackets Revised, now Rev2 (to prevent cracking) Update 04.02.24. Step files uploaded. This is my Triple Motor Z Axis Tilt project, for the Ender 7. This Z tilt setup is a little bit different from the norm…
When upgrading the main controller board to a Bigtreetech Manta e3eZ (or other Manta board) with a CB1 computer a new touchscreen is also required, as the stock Ender 7 screen is not compatible. This screen surround is for the BTT HDMI5…
Description: Lightweight Ender 7 replacement toolhead with direct drive extruder, integrated bed mesh probe, improved cooling and cosmetic appearance. Giving a clear view of the nozzle from above, perfect for watching the first print…
Updated 01.04.24, Revised back plate now Rev2 . Misaligned bolt hole corrected. Budget direct drive extruder, lower cost alternative to the Bondtech LGX Lite. Uses low cost HGX gear sets & 36mm pancake round stepper motor available from…
Description: Lightweight Ender 7 replacement toolhead with direct drive extruder, integrated bed mesh probe, improved cooling and cosmetic appearance. Giving a clear view of the nozzle from above, perfect for watching the first print…
Description: Lightweight Ender 7 replacement toolhead with direct drive extruder, integrated bed mesh probe, improved cooling and cosmetic appearance. Giving a clear view of the nozzle from above, perfect for watching the first print…
These are the additional parts that are required to complete the Crazylite 7 HGX direct drive extruder assembly. The HGX extruder uses the same commonly used 36mm diameter stepper motor as found on the Bondtech LGX lite extruder, with a…
This remix allows you to fit the LIBRA extruder with a ECAS04 Bowden connector.
These ae additional parts that are required to complete the Crazylite 7 assembly and are used on all versions. In this listing are two x-axis end stops, one for early Ender 7 s (mk1) & one for later Ender 7's (mk2). This part replaces the…
No re-wiring required. Ender 7 replacement toolhead with, bowden, or direct drive extruder and Pheatus Dragonfly HIC hotend. Giving a clear view of the nozzle from above, perfect for watching the first print layer going down. Cooling of…
02.12.23 Rev2. Probe Mount Face raised 0.66mm. New remix version with E3D Revo CR hotend & BIQU microprobe in place of Bambulab hotend & CRtouch. Note: See original CRtouch version for remaining files. Ender 7 replacement toolhead with…
Update: 27.04.20. Missing print support added. Description: Lightweight Ender 7 replacement toolhead with direct drive extruder, integrated bed mesh probe, improved cooling and cosmetic appearance. Giving a clear view of the nozzle from…
The original Bondtech LGX Lite extruder has recently been superseded by the new V2 version and has a two part body in place of the original four piece. Unfortunately the V2 two part body can no longer be used with many custom mounts as…
New remix version with BIQU microprobe in place of CRtouch. Note: See original CRtouch version for remaining files. There is also a E3D Revo CR remix version. Ender 7 replacement toolhead with direct drive extruder, integrated bed mesh…
Description: Lightweight Ender 7 replacement toolhead with direct drive extruder, integrated bed mesh probe, improved cooling and cosmetic appearance. Giving a clear view of the nozzle from above, perfect for watching the first print…
This is how I print my small ABS & ASA parts on the Ender 7 using a upside down box as a temporary enclosure. It maintains a chamber temperature of 35 to 40 degrees Celsius. Along with a ducted hotend cooling fan on the upgraded print…
These are all currently available results.
