Counting matching models…
ESP32-WROOM-32 Box (USB-C) A small box with snap-fit removable lid for the ESP32-WROOM-32 development board. Pins are still accessible from the underside via two slots. Please note this is for the 28mm x 52mm (approx.) PCB, this is the…
SIM Adapter Kit Card Simple set of SIM adapters in kit card form. Nano to mini Nano to micro Micro to mini Prints quickly, with no support. Snap out the one you need. Print at 0.16mm (0.2mm initial layer height) for best results. Take…
Giant Paperclip I'm not sure what else to say, its a giant paperclip and it measures 100mm x 28mm x 3mm. Print with an increased wall line count (4) to ensure strength.
Screw Caps for M3, M4, M5 and M6 Panhead Screws (Kit Cards) A set of screw caps with a flexure hinge, to tidy up the look of panhead screws. Common sizes of M3-M6 are covered. Print the card you need, snap out one of the caps, fasten the…
Radius Gauges Inner/Outer 1mm to 30mm Inner and outer radius gauges covering measurements from 1mm to 30mm in 1mm increments. There are a few of these models around, but I wanted something with large text that I could put on a wire loop…
Motorcycle Chain Lube Tool (525/530) Tool for lubrication of a 525/530 motorcycle chain. Print text down, no supports required. Use a releasable zip-tie through the channel to secure the tool to the aerosol. Cut the straw to length, so it…
Retro Cartridge Case for Nintendo Switch Games The main body features 2 print-in-place hinges and embossed details. Requires 4x 8x3mm round magnets to be superglued into the 4 recesses once printed, to hold the case closed. The insert is…
Digital Vernier Caliper Replacement Battery Cover A replacement battery cover for common, generic, vernier calipers. Prints on the face with the arrow on it, excellent bed adhesion is required as this is a small part.
A stand for the widely available temperature and humidity monitors. No supports required, print face down. The monitor snaps in with no tools.
Sunvisor Clip for Resqme Seatbelt Cutter and Glass Breaker A clip for storing the Resqme seatbelt cutter and glass breaker on your sunvisor. This will keep this valuable escape tool close to hand in the event you ever need to use it! More…
Thumb Turns for M4-M10 Bolts An assortment of thumb turns for M4, M5, M6, M8 and M10 bolts. They press fit on and are toleranced for a snug fit, while still being removable. 6 different designs for each size.
Linked Hearts Hanging Ornament A simple hanging linked hearts ornament that prints in place, pre-linked, with minimal support. Prints with minimal support, just a brim, because of the small contact areas. May need finishing on face that…
It is common for the tabs on the back of the 130mm centre cabs to break during removal. This glue-in insert can repair a broken tab and extend the life of the cap. Ideally print in ABS and use a solvent cement to glue the required amount…
Parkside Digital Vernier Caliper Replacement Battery Cover A replacement battery cover for the Lidl Parkside Vernier Caliper. As Lidl do not make these, I assume that it will be compatible with other equivalent vernier calipers. Prints on…
3M VHB Tape Mount for Resqme Seatbelt Cutter and Glass Breaker A 3M VHB tape mount for storing the Resqme seatbelt cutter and glass breaker in your vehicle. This will keep this valuable escape tool close to hand in the event you ever need…
Parkside Digital Angle Finder Replacement Battery Tray A replacement battery tray for the Lidl Parkside Angle Finder. As Lidl do not make these, I assume that it will be compatible with other equivalent angle finders. Prints flat with no…
Winding Road US Road Sign Magnet A magnet of the winding road warning sign used on roads in the United States. This is sized to accept a couple of 8x3mm magnets glued into the turrets on the rear. The images show the “right” version, but…
These are all currently available results.
