Counting matching models…
This is done with a half size grid, it's compatible with a normal gridfinity grid but you can place it at half offsets, and the model itself is sized equivalent to 5.5x6 grid. Heavily inspired by…
Other models I found were too tight, held them vertically or the tip storage was too short Holds 1x Pinecil v2 4x Tips(tried with https://www.amazon.com/dp/B07NPKK1PB which is longer than the tip that came with my Pinecil)
Holds 4 rockler bench cookies. https://www.rockler.com/bench-cookie-plus-work-grippers-4pack
This is done with a half size grid, it's compatible with a normal gridfinity grid but you can place it at half offsets, and the model itself is sized equivalent to 5.5x6 grid. Heavily inspired by…
Holds the short 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24 mm Tekton Sockets. The models also includes pegs at the bottom, not sure how useful they actually are 🤷
Holds 60x40 Kinex Machinist Square https://taytools.com/products/kinex-machinist-square 100x70 Kinex Machinist Square https://taytools.com/products/kinex-2-piece-din-875-1-machinist-squares 200x130 Kinex Flat Machinist Square…
Remix that includes a hole for a rotary encoder from a fan controller to fit through
See the final image for what fits in each column, the first column is for accessories with male fittings attached to sit in. In v2 the 2nd column that holds male fittings was loosened a bit, at first after printing v1 holds the connectors…
Holds the 3 bits from https://www.amazon.com/dp/B0000TZX1M
Built for this set https://www.amazon.com/dp/B09QXYLRPD The print I did didn't have correct length on the 2 side pieces but it's fixed in the uploaded file. For the multicolor with text I used .2mm layer height and changed the color for…
I used this to mount an optical drive to the underside of my desk. The pcb mount file is for the PCB from https://www.amazon.com/dp/B01MRUN0HQ (at least from the 2 I bought in 2018, may have changed in the time since)
Holds a Kunz Block Plane #9 ½ https://www.amazon.com/dp/B0042ADRDG There's an indented area with quite a bit of wiggle room so that you aren't setting it down on the blade. For the multicolor with text like mine is I printed with .2mm…
Used the shadow created by @ds to create a 6u high version (with a label) that lets the stripper sit fully below the top
Can mount the holder to the wall using 3m command strips and then slid the airgradient in and out. I've upgraded a few sensors & had to debug stuff on my airgradient and it was annoying to take off the wall previously. The file attached…
Holds the 3-peice Montana Brand plug cutters https://www.amazon.com/dp/B001DT3A1S https://www.rockler.com/3-pc-self-centering-plug-cutter-set
I have a 3M command strip underneath the controller to hold it in place & a cut down 3M command strip holding the Fingerbot in place. I needed a small extension for the fingerbot arm, I used…
Press fit wheel that goes over the panavice jr jaw screw, fits snugly.
Countersink Replacement Bit Set Uses have grid sized base, works fine with standard 42mm plates but allows offsetting by 1/2.
Holds 17 RFID housing bits from Mark G's adapters. https://makerworld.com/en/models/841663-universal-rfid-spool-adapter-for-ams#profileId-788009…
Holds the Pinecil & 6 tips. The base has half sized gridfinity grid. It will fit onto a standard gridfinity base plate but will allow you to offset by 1/2. It's 2.5x3 grids on a standard 42mm grid
These are all currently available results.
