Counting matching models…
Print in PETG at least. Some parts are a tight fit, the spacer plate and the vent clips. Everything else should have enough clearance. use 4 M3x8 screws for the cover. For phone widths from about 62 to 102mm, it is really a fiction…
Egg yolk separator for cup/jug sizes 4-7mm
The ribbon twister should be printed with the cable entry side on the bed without supports. Cable clips will possibly need a raft.
Updated: 9 Aug 2023 - Added a frame with an SD card slot Shaped better, cover fills the full face, hinge point moved back and changed the retaining bumps. Use a piece of filament as a hinge pin to connect the flap to the frame.
I use this in a water removal vacuum device. Water is sucked off the floor into a bucket, the vacuum keeps the check valve closed. When the vacuum is turn off the bucket drains through the check valve. So it's not meant to be a perfect…
Update : There's a better one here Printed on my Ender for fun.
Make a CR-Touch mountable after breaking the fragile mounting tabs. Category: 3D Printer Accessories
This a redesign of a popular model I made a few years ago, most phones have increased in size. Also the tolerances afforded by Bambu Lab machines make it much easier to print and assemble. It suits phones up to 12mm thick. 4 screws M3 x 8…
This is a veroboard based project using an ESP32 Devkit (node32s) dev board. But should be suited to any dev board. Requires:- Long header pins Digital Pot/Rotary Encoder with push button ESP32 board 1.3" 128x64 I2C OLED Display Veroboard…
As most of these designs are too narrow for AUS tubes, I had to make my own. There are no flexing parts that will break over time, the key is held in place by the torque from the tube wanting to unwind. This makes it grip more and hold…
Use 7 pieces of filament about 6-8mm long to make location pins for gluing. Make sure the faces mate flush before gluing with CA. Sides need a bit of smoothing with sand wet sandpaper.
The supplied 6mm tube doesn't appear bend, and the grommet creeks and squeaks like and old wooden ship.
Seen them online but cannot pay $40 for a print when I have a printer and can draw :D I did a couple of test prints in PLA before using TPU. Even PLA (pictured) ones seem to fit and work just fine. Enjoy.
Yet another spool holder. It has a fast, 2-start thread (16mm pitch) for quick loading and unloading. The end bearing is smaller to allow for a unthreaded lead for easier threading. The thread tooth has 45 degree sides so it prints great,…
The text is embedded in the part, split to parts if you want to color them.
Olive oil spout for most glass bottles. It allows the run off to drip back into the bottle. Print the gasket in tpu, and everything else in whatever you want. no supports needed Print Settings Printer Brand: Creality Printer: Ender 3…
Need 4 M3x12mm screws. The usb charger module is only supplying 5v to the WT32. Category: Electronics
Print in PETG or food safe PLA (to keep the 3D printing equivalent of spelling bees at bay). Change colour for a nice touch. Sand the blade with a sanding block to remove the layer step lines. Category: Kitchen & Dining
Easy to access magnetic lid. The lid's clearances are 0.1mm all round, I printed mine on an Ender 3 variant with a 0.6mm nozzle in PETG. The bottom lids needs supports, I used supports on the container. You'll need 2 or 3 of 8x3mm magnets…
You should know what to do Category: Electronics
The LED inser needs to be glued with CA and sanded flush with the back of the case. Without glue the ESPs get warm and the top bit opens up if printed in PLA. I use these on 2 ender 3v2's Fluidpi. You need to crack the green glue locking…
UPDATE:30/03/23: Added a one piece print with supports base. A kitchen sink tool drainer. Supports only needed for the mesh. you need 4 small self tapping screws to mount the feet. M3 countersunk screws should work too. Print Settings…
Press fit 2 magnets 8x3mm. make sure the poles are the right way before dong the 2nd one.
A small pot for starting seeds. the raised base keeps it out of the water and also allows light to get to the base to stop the roots growing thru the mesh. Look at the 3mf file to see how to print the mesh. adjust the infill size to suit…
Hang some metric ring spanners on your toolboard. Need 3 suitable wood screws.
A fan cover for the Creality Sprite non kit version. Gives you something to press on when inserting filament. You need 2x M2 x 16mm. It's best to remove the fan duct and check the length of the screws, if they are too long they will push…
Folds around the PCB to prevent shorting on tools. Print at 0.2mm layers. Fold it up while it's still warm but don't clip it in yet and let it cool. You'll need to trim down the thru hole pins. Insert a piece of filament as light pipes…
Print without supports. Required: 20mm conduit 200-300mm long 3mm carbon fibre tube or similar. Reprap Endstop limit switch 2x M3x12 screws. The flag and float need to be assembled with CA glue, make sure you have it through the body…
Print with supports and clean up the hinge pin faces, Use a piece of filament for the pin heat and mushroom the end over over with something. There are versions for pipe sizes 2.2 - 3.0mm but you w8ll need to clean up the hole with a dril…
Need 2 M4/M5 bolts and t-nuts. Print with supports.
Some small supports needed, see pictures. Make sure you block supports in the small hole in the adjuster. The 2 plastic parts should have extra walls and infill as it will take abuse. The TPU parts can be normal 2 walls etc as you want…
Extends the length of the filter so that you can grind a double shot in one go without messing coffee ground s everywhere. This is based on the one which Breville now supplies with the machines. Tamp the coffee through the extender then…
Having built-in WiFi is nice, but not for bed levelling and quick z offset adjustment. But it could be used for anything else. If your screen has nuts it shouldn't need the spacer. If not the spacer provided can be cut down to size in…
After using @Simbungu's awesome model https://www.printables.com/model/80817-breville-barista-express-single-dose-hopper for a while… I was having to be too careful when adding the beans, one or two would fall behind the machine affecting…
These are all currently available results.
